Browsing School of Microelectronic Engineering (FYP) by Title
Now showing items 4-23 of 153
-
All optical memory
(Universiti Malaysia Perlis (UniMAP)School of Microelectronic Engineering, 2011)This project describes about all-optical memory comprises of three optical inputs with one modulated data signal at the transmission circuit and supports by another two control pulses circuits. These three inputs injected ... -
All-optical CSRZ generator
(Universiti Malaysia Perlis (UniMAP)School of Microelectronic Engineering, 2010-04)The Carrier-Suppressed Return-to-Zero (CSRZ) conversion signal is an optical modulation format used in high bit rate transmission system and long-haul data transmission. The characteristics of CSRZ provide a better ... -
All-optical shift register
(Universiti Malaysia Perlis (UniMAP)School of Microelectronic Engineering, 2011-04)The all-optical shift register is demonstrated in which it is based entirely on semiconductor optical amplifier (SOA). The shift register is formed by the combination of an SOA in a fibre loop mirror. SOAs are used for ... -
Analogue digital converter for e-tongue application
(Universiti Malaysia Perlis (UniMAP)School of Microelectronic Engineering, 2011-06)This work presents a report on designing analogue digital converter (ADC) for e-tongue application. In work for convert an analogue signal from the measurement subject to digital signal which is will be process by another ... -
Analysis & design low power multiplier using TSMC 0.18µm CMOS technology
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)As the advance of VLSI technology, low power design has become an important topic in VLSI design. This project is to design a low power multiplier implemented in mentor graphic tools. Low power multipliers are developed ... -
Analysis of square shaped Microstructure based Electron Beam induced deposition
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)The fabrication of square shaped microstructures is studied by electron beam induced deposition (EBID) method using Scanning Electron Microscopy (SEM). EBID is a technique that allows the resistless deposition directly ... -
Analysis of Switched Mode Power Supply (SMPS) with Energy Saving Requirement
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2007-04)Nowadays, the Switched-Mode Power Supply (SMPS) plays an important role in the consumer power market. With its small size, it can be found everywhere from mobile phone chargers to Plasma TVs or even in compact dics players ... -
Analysis of the deposited carbon during Electron Beam Induced Deposition (EBID) in Scanning Electron Microscope using Secondary Ion Mass Spectrometry (SIMS)
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-03)Many experiments on the mechanics of nanostructures require the creation of rigid clamps at specific locations. In this work, electron beam induced deposition (EBID) has been used to deposit carbon films that are similar ... -
Analysis the role of supply voltage and load capacitor in small-signal MOSFET amplifiers
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-03)The main objective of this project is to investigate the role of supply voltage and load capacitance in the performance of small-signal MOS amplifier with the PSpice simulation for the Common Source, Common Gate and Common ... -
Automated Car Safety Enhancement System
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2007-04)Automated Car Safety Enhancement Systems (ACSES) is a system that designed to prevent accidents or to minimize the force and damage of collision in case of accidents. The goal of this system is to help avoiding vehicle ... -
BST Sensor Application: Digital Thermometer
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2007-03)This thesis deals with the research of Barium Strontium Titanate (BST) sensor and its application as digital thermometer. In general BST sensor was still in research stage, because this sensor is the first BST sensors that ... -
BST Sensor Application: Programmable Night Lamp With Morning Alarm
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2007-03)A high potential BST Sensor fabricated at UniMAP’s Clean Room was left unused from any further development even though it has good characteristics. The main aim for this project is to develop an application system prototype ... -
BTST Thin Film Sensor Application: Heat Indicator
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2007-03)This report contains an account of my final year project, which was carried out in the forth year of the Electronic Engineering (B.Eng) degree at Universiti Malaysia Perlis. This paper is based on the design and analysis ... -
Car Reverse Sensor with distance display
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-03)Car reverse sensor with distance display is a design to improve driver awareness in maneuvering reversed gear. The design also helps deaf person to benefit from today technology. The distance displays fast enough to give ... -
Characterization of Electroless Under Bump Metallurgy for Alsi Bond Pad Composition
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2007-03)The characterization of electroless under bump metallurgy for AlSi bond pad composition in term of surface morphology and surface roughness was investigated. By using the sample given, the gold layer need to be deposited ... -
Characterization of Intermetallic Growth in Gold Ballbonds on Aluminum Metallization
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2007-03)The objective of this project is to study the capability of gold wire bonding process by investigating the intermetallic growth between gold ball bonds and aluminum bond pad. The study includes applying thermal storage ... -
CMOS Two Stage OP-AMP analysis and design
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-03)The design and analysis CMOS of Two Stage Operational Amplifier that presented has constructed with two basic amplifier which is diffential amplifier and single stage amplifier. The design need to achieve the value that ... -
Coherent effect on LOCOS and STI technique for 0.18 µm CMOS technology using Taurus Workbench
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)LOCOS (Local Oxidation of Silicon) and STI (Shallow Trench Isolation) are two isolation techniques used in integrated circuit fabrication. Further device scaling using LOCOS technique is no longer practical for technology ... -
Comparison of delays between 4-bits ripple-carry adder and 4-bits carry look-ahead adder using logical effort method
(Universiti Malaysia Perlis (UniMAP)School of Microelectronic Engineering, 2011-06)In this project, two types of circuit topologies has been designed which are the 4-B its Ripple-Carry Adder Circuit (RCA) and the 4-Bits Carry Look-Ahead Adder Circuit (CLA). Delays in RCA circuit will be compared between ... -
Comparison Of Etching Optimization Process By Taguchi Method Using Minitab And Design Expert Software
(School of Microelectronic Engineering, 2007-04)A design of experiment for high throughput pad etch by reactive ion etch is reported. Design of Experiment (DOE) is a technique for optimizing process which has controllable inputs and measurable outputs. The L9 orthogonal ...