Browsing Mohd Mustafa Al Bakri Abdullah, Prof. Dr. by Title

Now showing items 15-34 of 277

    • Calcined kaolin geopolymeric powder: Influence of water- to geopolymeric powder ratio 

      Liew, Yun Ming; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr.; Mohd Mustafa Al Bakri, Abdullah; Binhussain, M.; Luqman, Musa, Dr.; Khairul Nizar, Ismail, Assoc. Prof. Dr.; cheng, Yong Heah (Trans Tech Publications, 2012-07)
      This paper describes the synthesis of calcined kaolin geopolymeric powder from the alkaline activation of calcined kaolin followed by solidification and pulverizing process. The geopolymeric powder was used by just adding ...

    • Ceramic Waste Concrete (CWC) 

      Mohd Mustafa Al Bakri, Abdullah; Che Mohd Ruzaidi, Ghazali, Assoc. Prof.; Norazian, Mohammed Noor; Norzaidi, Zainol (Kementerian Pengajian Tinggi Malaysia (KPTM), 2007-08-10)

    • Characterisation at the bonding zone between fly ash based geopolymer repair materials (GRM) and ordinary portland cement concrete (OPCC) 

      Warid Wazien, Ahmad Zailani; Mohd Mustafa Al Bakri, Abdullah; Mohd Fadzil, Arshad; Rafiza, Abd Razak; Muhammad Faheem, Mohd Tahir; Remy Rozainy, Mohd Arif Zainol; Nabiałek, Marcin; Sandu, Andrei Victor; Wysłocki, Jerzy J.; Błoch, Katarzyna (MDPI AG, 2020-12)
      In recent years, research and development of geopolymers has gained significant interest in the fields of repairs and restoration. This paper investigates the application of a geopolymer as a repair material by implementation ...

    • Characteristics of thermoplastic potato starch/bentonite nanocomposite film 

      Nurul Husna, Zakaria; Noorhafiza, Muhammad; Mohd Mustafa Al Bakri, Abdullah; Sandu, I. G.; Mei Wan, C. L. (IOP Publishing Ltd, 2018-06)
      The aim of this study is to investigate the effect of bentonite towards thermoplastic potato starch nanocomposite films on the mechanical, microstructure and physical properties. The nanocomposite films were prepared using ...

    • Characterization of geopolymer ceramic reinforced Sn-0.7Cu composite solder: effect of milling time and speed 

      Mohd Arif Anuar, Mohd Salleh; Mohd Mustafa Al Bakri, Abdullah; Thiaghu, Maiteli; Nur Syahirah, Mohamad Zaimi; Romisuhani, Ahmad (IOP Publishing Ltd, 2019-12)
      The effect on the addition of optimally ball milled kaolin and fly ash geopolymer ceramic as reinforcement on the morphology and electrical properties of Sn-0.7Cu composite solder were explored. Geopolymer ceramics from ...

    • Characterization of LUSI mud volcano as geopolymer raw material 

      Mohd Mustafa Al Bakri, Abdullah; Rafiza, Abdul Razak; Djwantoro, Hardjito, Dr.; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr.; Khairul Nizar, Ismail, Assoc. Prof. Dr. (Trans Tech Publications, 2012)
      The mud of mud volcano samples were collected from an eruption site named 'LUSI' (Lumpur "mud" -Sidoarjo), East Java, Indonesia for characterization. Analysis showed that, the major constituents of mud are SiO 2 and Al 2O ...

    • Characterization of LUSI mud volcano as geopolymer raw material: A review 

      Rafiza, Abdul Razak; Mohd Mustafa Al-Bakri, Abdullah; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr.; Djwantoro, Hardjito, Dr. Ir.; Khairul Nizar, Ismail, Assoc. Prof. Dr. (Universiti Malaysia Perlis (UniMAP), 2012-06-18)
      This paper summarizes the current knowledge about the potential of LUSI mud volcano, East Java, Indonesia as a raw material in geopolymer. Previous experimental study shows that the LUSI mud has a good performance when 5% ...

    • Chemical and physical characterization of boiler ash from palm oil industry waste for geopolymer composite 

      Zarina, Yahya; Mohd Mustafa, Al Bakri Abdullah; Kamarudin, Hussin; Khairul Nizar, Ismail; Andrei Victor, Sandu; Petricǎ, Vizureanu; Rafiza, Abdul Razak (Syscom 18 SRL/ SC BIBLIOTECA CHIMIEI SA, 2013-12)
      The characterizations of boiler ash waste from waste of palm oil industry were performed. The boiler ash was obtained from the boiler in the palm oil processing factory. The chemical and physical characterization has been ...

    • Chemical reactions in the geopolymerisation process using fly ash-based geopolymer: A review 

      Mohd Mustafa Al Bakri, Abdullah; Kamarudin, Hussin; Mohammed Amjad, Hussain; Khairul Nizar, Ismail; Rafiza, Abdul Razak; Mohd Izzat, Ahmad (American-Eurasian Network for Scientific Information (AENSI Publisher), 2011-07)
      The development of our world, demanding the power supply which is produced by combustion of coal. Unfortunately, the million of tons of fly ash and related-products have been generated. To overcome these problems, fly ash ...

    • Coagulation-flocculation process in landfill leachate treatment: focus on coagulants and coagulants aid 

      Mohamad Anuar, Kamaruddin; Mohd Mustafa Al Bakri, Abdullah; M S, Yusoff; Alrozi, R; Neculai, O (IOP Publishing Ltd, 2017-06)
      In physico-chemical treatment, the separation of suspended particles from the liquid phase is usually accomplished by coagulation, flocculation and sedimentation. Coagulation-flocculation processes have been widely used ...

    • Compaction optimization of Sn-Cu-Si3N4via powder metallurgy route for composite solder fabrication 

      Muhamad Hafiz, Zan @ Hazizi; Mohd Arif Anuar, Mohd Salleh; Zainal Arifin, Ahmad, Prof.; Mohd Mustafa Al-Bakri, Abdullah; Alida, Abdullah; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr. (Trans Tech Publications, 2013)
      The aim of this study was to optimize the compaction process of a composite solder fabricated via powder metallurgy route, before details study were conducted in the next stage. Powder of Sn, Cu and Si3N4 were carefully ...

    • A comparative study of solder properties of Sn-0.7Cu lead-free solder fabricated via the powder metallurgy and casting methods 

      Mohd Arif Anuar, Mohd Salleh; Mohd Mustafa Al Bakri, Abdullah; Sandu, Andrei Victor; Norainiza, Saud; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr.; McDonald, Stuart D.; Nogita, Kazuhiro (Syscom 18 SRL, 2013-07)
      The properties of Sn-0.7Cu solder bulk prepared via the powder metallurgy (PM) method were investigated and compared with solder bulk fabricated through casting. Distinct microstructures were observed in both PM and casting ...

    • Comparative study on thermal, compressive, and wear properties of palm slag brake pad composite with other fillers 

      Che Mohd Ruzaidi, Ghazali, Assoc. Prof.; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr.; Shamsul, Baharin Jamaludin, Prof. Dr.; Mohd Mustafa Al Bakri, Abdullah (Trans Tech Publications, 2011)
      The attractive performance-to-cost ratio associated with the incorporation of waste material in composite formulations used to produce brake pads has stimulated the idea of exploring the possible incorporation of additional ...

    • The comparison between four PLCC packages and eight PLCC packages in personal computer (PC) using computational fluid dynamic (CFD), fluent software™ using epoxy moulding compound material (EMC) 

      Mazlan, Mohamed; A. Rahim; Iqbal, M. A.; Mohd Mustafa Al Bakri, Abdullah; Wan Yusra Hannanah, Wan Abdul Razak; Mohd Sukhairi, Mat Rasat (Trans Tech Publications, 2013)
      The paper present the three dimensional numerical analysis of heat and fluid flow through Plastic Leaded Chip Carrier (PLCC) packages in inline orientation horizontally mounted on a printed circuit board in a wind tunnel ...

    • Comparison of geopolymer fly ash and ordinary Portland cement to the strength of concrete 

      Mohd Mustafa Al Bakri, Abdullah; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr.; Mohamed, Bnhussain, Prof. Dr.; Khairul Nizar, Ismail, Assoc. Prof. Dr.; Rafiza, Abdul Razak; Zarina, Yahya (American Scientific Publishers, 2013-12)
      The aim of this study is to evaluate the effect of various fly ash: aggregate ratios by using fly ash (FA) based geopolymer compared to ordinary Portland cement (OPC) on the compressive strength of concrete. The different ...

    • Comparison of original and sintered LUSI mud from East Java, Indonesia as raw material for making a geopolymer 

      Rafiza, Abdul Razak; Mohd Mustafa Al Bakri, Abdullah; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr.; Djwantoro, Hardjito, Dr.; Khairul Nizar, Ismail, Assoc. Prof. Dr. (American Scientific Publishers, 2013-01)
      This paper presents the characterization of LUSI mud from East Java, Indonesia, as a potential raw material for making a geopolymer. Two types of LUSI mud were analyzed, i.e., original LUSI mud and LUSI mud that had been ...

    • Comparison of Rubber as Aggregate and Rubber as Filler in Concrete 

      Mohd Mustafa Al Bakri, Abdullah; Syed Nuzul Fadzli Syed Adam; M. D. Abu Bakar; K. W Leong (Universiti Malaysia Perlis (UniMAP), 2007-06-09)
      This research will attempt to use rubber waste (tire rubber) replacement of coarse aggregate to produce early age concrete. An experiment will carry out to determine the strength of early age concrete with rubber waste ...

    • Compressive strength and morphology of fly ash based geopolymer as artificial aggregate with different curing temperature 

      Alida, Abdullah; Mohd Mustafa Al Bakri, Abdullah; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr.; Che Mohd Ruzaidi, Ghazali, Prof. Madya; Zarina, Yahya; Mohd Arif Anuar, Mohd Salleh; Nurhamidah, Zakaria; Muhammad Faheem, Mohd Tahir (Trans Tech Publications, 2014)
      This paper presented the compressive strength of geopolymer paste with different NaOH concentration and morphology analysis for sintered artificial aggregate. This artificial aggregate was produce based on mix design with ...

    • Compressive strength and thermal conductivity of metakaolin geopolymers with anisotropic insulations 

      Nur Ain, Jaya; Yun-Ming, Liew; Mohd Mustafa Al Bakri, Abdullah; Kamarudin, Hussin; Cheng Yong, Heah; Ridho, Bayuaji; Muhammad Faheem, Mohd Tahir (IOP Publishing Ltd, 2020-02)
      This research investigated the properties of thermally insulating geopolymer prepared using waste filler (fibreboard and rubber) to act as anisotropic pore/insulation. The geopolymer matrix was synthesised using metakaolin ...

    • Compressive strength of fly ash based geopolymer / glass fiber composite via filament winding 

      Che Mohd Ruzaidi, Ghazali, Prof. Madya; Alida, Abdullah; Mohd Mustafa Al Bakri, Abdullah; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr.; Anis Nadhirah, Ismail (Trans Tech Publications, 2014)
      In general, filament winding technique is used to fabricate the composite pipes using continuous fiber and matrix resin. In this study, fly ash based geopolymer resin composites reinforced by continuous glass fiber were ...