Browsing School of Manufacturing Engineering (FYP) by Title
Now showing items 297-316 of 336
-
The study of value stream mapping (VSM) and Kanban in an automotive parts manufacturer
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)This research addresses the application of lean manufacturing concepts to the continuous process sector with a focus on the production manufacturing plant. The goal of this project is to make an improvement by applying ... -
A study of warpage and weld line defects on a plastic composite’s manhole cover
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)Manhole covers are generally made out of cast iron in order to bear the large loads [1]. This study is about choosing and identifying the most suitable plastic composites material which can best replaced cast iron The ... -
A study of warpage and weld line in a composite motorcyle engine oil cover using mold flow analysis software
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010)Today’s emphasis is placed on lowering production cost and weight. By replacing the metal with plastic composites, it is said to be achieved the goals compared with aluminum equivalent. Motorcycle engine oil cover is a ... -
A study of warpage and weld line in a composite motorcyle engine oil cover using mold flow analysis software
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2014)Today’s emphasis is placed on lowering production cost and weight. By replacing the metal with plastic composites, it is said to be achieved the goals compared with aluminum equivalent. Motorcycle engine oil cover is a ... -
The study of yamazumi board in an automotive parts manufacturer
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010) -
A study on contraction of Pneumatic Artificial Muscle (PAM) for load-lifting
(Universiti Malaysia Perlis (UniMAP), 2016-06)Pneumatic Artificial Muscle (PAM) is a type of actuator that similar to human muscle. The PAM is used for converting pneumatic power to pulling force and eventually causing movements of the mechanism. One of the potential ... -
A study on design and develop a concurrent problem solving method in mould flow analysis
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2009-05)CAE techniques have in recent years, become increasingly popular in plastic injection molding. However, in most practices, either molding parameters are not optimized or the optimization techniques are too complex to use. ... -
A study on different localities of Soft Exoskeleton for hand grasping using pneumatic actuator
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project is related to the soft exoskeleton for hand grasping using pneumatic actuator on different localities. The device is lightweight and easy wearable due to the usage of soft pneumatic actuator. The number of ... -
Study on effects driver’s postures on comfort during driving
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)Driving is an aspect in life that sometimes we can’t avoid. Be in short distance or in long distance, overtime, back ache and neck tension can results for being in one spot with the wrong posture for far too long. A ... -
A study on energy efficient building
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2009-04)This study is about the ways and factors that could be use in achieving the efficiency of energy use may it in a building or for residential uses. By taking the consideration of present energy crisis, the factors are analyze ... -
A study on Miniature Compressed Air Storage System using Double-Acting Cylinder for portable device
(Universiti Malaysia Perlis (UniMAP), 2016-06)Nowadays, there are many research study on the pneumatic device on vehicles. There is some application using compressed air storage system to produce vehicle power. However, there are some troubles facing to produce ... -
A study on miniature compressed air storage system using double-acting cylinder for portable device
(Universiti Malaysia Perlis (UniMAP), 2016-06)Nowadays, there are many research study on the pneumatic device on vehicles. There is some application using compressed air storage system to produce vehicle power. However, there are some troubles facing to produce ... -
A study on surface roughness of aluminium using CNC milling process
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)The commonly problem for milled product is quality of surface roughness. Therefore, the important step is with choice the correct cutting parameter to get the result or to obtain desired surface finish. This project was ... -
A study on surface roughness of cast iron using CNC milling process
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)Surface roughness is one of the aspects that are of great significance in CNC milling process as it represents the quality of the product. Thus, in order to obtain a good surface finish, optimum cutting parameters in CNC ... -
A study on surface roughness of wood using CNC milling process
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)The important aspect in machining process is the quality of milled product surface. Therefore, the choice of current cutting parameter is very important in order to obtain the desired surface finish. Thus, measuring and ... -
A study on surface roughness of wood using CNC milling process
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010)The important aspect in machining process is the quality of milled product surface. Therefore, the choice of current cutting parameter is very important in order to obtain the desired surface finish. Thus, measuring and ... -
A study on the machining parameters optimization of WEDW machining TI-6AL-4V: effect on surface roughness, MRR and cutting speed
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)The purpose of this project is to optimize the WEDM combination parameters in order to get the highest material removal rate (MRR), fastest cutting speed (CS) and finest surface roughness (SR) on material of titanium alloy ... -
A study on the use of high pressure application for destruction of microorganism in soymilk
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)The current method of soymilk processing proved to be degrading to the quality of milk and its product. Due to this, this project was carried out for the purpose of investigating the application of ultrasonic wave as an ... -
Surface modification of 316L stainless steel by using pulsed laser
(Universiti Malaysia Perlis (UniMAP), 2016-05)Coronary stent is a mechanical medical devices design to open the arteries that have been affected by coronary artery disease (CAD). Blood vessel obstruction is the result of atherosclerosis by the buildup of smooth ... -
System to reduce and optimize inventory at engineering room
(Universiti Malaysia Perlis (UniMAP), 2016)Nowadays, most companies and factories do not realize that the management made a waste of money, time and cost of such inventories, transportation, overprocessing, over-production, waiting time and motion products. So, ...