Browsing School of Manufacturing Engineering (FYP) by Title

Now showing items 259-278 of 336

    • Quality improvement of production line by using Hikarimono activity for automobile industry 

      Mohd Hafiz, Asari (Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2009-05)
      The most important department in industry is the production department. The smooth in production flow beginning from the raw material to the product is important and need to maintain it. There are several improvements ...

    • Rainwater Catchment System - roofing 

      Fatimah Topit (Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)
      Rainwater Catchment System is a system that uses rainwater as the water sources for activities such cooking, washing, bathing and others activities that involved water utilization. This system is mostly applied at urban ...

    • Rainwater Catchment system – storage tank 

      Masita Raja Mohammad (Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)
      Rainwater Catchment System is a system that collects rainfall from the catchment area and will be store in the water storage tank. This rainfall collection will be used as the water sources for activities such cooking, ...

    • Redesign and improvement the effectiveness of automatic plant waterier 

      Mohamad Aiman, Azhar (Universiti Malaysia Perlis (UniMAP), 2016-06)
      This project is to redesign an automatic plant waterer for domestic purpose. In order to develop an effective drip irrigation system to the automatic plant waterer, the special design of emitter and electronic sensing ...

    • Reducing cycle time in semiconductor manufacturing process 

      Lim Yee, Chew (Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)
      This study concerns the Test Probes a semiconductor manufacturing process improvement. It is learned through the process flow and by collecting the required process time of the production line, then determined the causes ...

    • Reduction of coating time for catheter process 

      Nur Farah Hanum, Zakaria (Universiti Malaysia Perlis (UniMAP), 2016-06)
      The coating process is the process for covering up to the surface outer of catheter. This study was conducted in order to reduce the time for coating process in manufacturing catheter by using the process flow method. ...

    • Reject reduction in fiber board corrugated manufacturing using DMAIC approach 

      Mohamad Fadli, Abdul Razak (Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)
      This study deals with to ‘Reject reduction in fiber board corrugated manufacturing using DMAIC approach’. The purpose of this study has been to better understand how DMAIC Methodology can be applied successfully in an ...

    • Reliability and maintainability analysis: a case study of production line in process tyre industry 

      Khairul Annwar, Abd Rahman (Universiti Malaysia Perlis (UniMAP), 2016-06)
      Reliability and maintainability analysis is used to ensure adequate performance of the system based consistently with minimal maintenance costs. Both combinations determine on how the proportion of time for use or matter ...

    • Reusability of plastic 

      Ng Lim Yong (Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008)
      Plastic is light, easy to store and transport, comes in variety of textures and shapes and can hold almost anything. Those properties make it attractive to manufacturers and packagers, who use it for any application. A ...

    • Reusability of plastics 

      Sing Peir Ming (Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)
      It is a challenge to reduce the ever-increasing flow of plastics waste. This study was undertaken to investigate the viability of recycling plastics products and their capabilities in substituting virgin plastics in the ...

    • Robust setting of Ti-6Al-4V machining using WEDM (High Energy with EF Circuit Off) 

      Muhammad Noor Aliyas (Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)
      The purpose of this project are to optimize process variables of WEDM to obtain maximum MRR and minimum surface roughness in rough cutting. This project started with collecting the information from literature review regarding ...

    • Robust setting of Ti-6Al-4V machining using WEDM (High energy with EF Circuit Off) 

      Mohamad Nazeri Yahaya (Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)
      In this project, some research had been done on optimization of wire electrical discharge machining (WEDM) parameters. It has been known that WEDM is a specialized thermal machining process which accurately machines parts ...

    • Robust setting of Ti-6Al-4V machining using WEDM (High Energy with EF Circuit ON) 

      Raja Safwan Bin Raja Sulaiman (Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)
      In this project, four Wire EDM parameters (On Time, Off Time, Peak Current and Wire Speed) were manipulated to achieve the robust setting on material removal rate (MRR) and surface roughness (Ra) using Ti-6Al-4V titanium ...

    • Robust setting of Ti-6Al-4V machining using WEDM (Low Energy with Electrolysis Free Circuit Off ) 

      Mohd Fauzely Mustapa Bakari (Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)
      Titanium alloys such as Ti-6Al-4V are increasingly used in aerospace and automotive industries, and also used as medical implant material in wide variety of applications. Wire-electro discharge machining (WEDM) is an ...

    • The role of continuous improvement in an organization 

      Nor Azila, Ali (Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2009-05)
      This report presents the study on the continuous improvement method that has been implemented at the industry in Malaysia. This study also involved in the challenges and benefits of implementing this method. A questionnaire ...

    • Shrinkage and warpage on front panel housing using Genetic Algorithm (GA) 

      Muhammad Ezuddin, Shafiee (Universiti Malaysia Perlis (UniMAP), 2016-06)
      In materials processing, quality and productivity are most important and must be controlled for each product type produced. In an injection moulding process, quality is measured in term of warpage of moulded parts while ...

    • Simulation of tensile behavior of FRP composite material using finite element analysis 

      Tan, Jun Kang (Universiti Malaysia Perlis (UniMAP), 2016-06)
      Fiber reinforcement polymer (FRP) composites material possesses excellent properties such as high specific stiffness, high strength-to-weight ratio, resistance of corrosion and weariness. However, number of factors control ...

    • Simulation on usage of water to an explosive compaction 

      Nor Azmaliana, Azmi (Universiti Malaysia Perlis (UniMAP), 2016-05)
      This project is about the simulation on usage of water to an explosive compaction. The explosive compaction is a method to compress the metal powder into desired shape. Emulex is used as an explosive in this project. The ...

    • Solar food dryer 

      Nor Amalina Muhayudin (Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)
      Solar thermal systems is a practical, economical and the responsible approach environmentally for drying operation, which is applicable to almost all the agricultural product. By means of that, in this project, Solar ...

    • Stabilization of production rate for plastic products (Single CD) by using injection moulding machine 

      Chew Pei Pei (Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)
      A researched project was designed in order to study the stabilization of production rate for plastic product (single CD) by using injection moulding machine. The study was carried out by identifying the operating parameters ...