Browsing School of Manufacturing Engineering (FYP) by Title
Now showing items 179-198 of 336
-
Impact strength on thin-walled tubes
(Universiti Malaysia Perlis (UniMAP), 2016-05)Energy absorber has found common usage in application such as vehicle, aircraft and at base of lift shaft. Circular thin-walled tubes had been years for functioning as efficient energy absorbing devices but as decompose ... -
Implementation of Lean Technique 5S at Corrugated Fiberboard Carton industry
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)In organizational development, process improvement is a series of actions taken to identify, analyze and improve existing processes within an organization to meet new goals and objectives. Therefore, implementation of 5S ... -
Improvement in leaching process for natural rubber latex production of Urethral Foley Catheter
(Universiti Malaysia Perlis (UniMAP), 2016-05)Urethral catheters of natural rubber latex were soaked in distilled water with two types of flow water pipes which are at the top of the tank (upwards) and at the bottom of the tank (downwards). The effects of soaking in ... -
Improvement of coffee powder weight on nitrogen packing process using Lean And Six Sigma approaches
(Universiti Malaysia Perlis (UniMAP), 2016-06)Continuous improvement process (CIP) is a tradition of constant improvement focusing the elimination of defect and waste in all systems and processes of an organization. The defects and waste defined as anything that is ... -
Improvement of filter paper packing defects using Lean and Six Sigma approaches
(Universiti Malaysia Perlis (UniMAP), 2016-06)The black dot defect is a condition where coffee powder melt on filter paper while producing coffee sachet. This study was conducted in order to reduce black dot defect in producing coffee sachet by using Continuous ... -
Improvement of plastic roll change process on primary packing machine using Lean and Six Sigma approaches
(Universiti Malaysia Perlis (UniMAP), 2016-06)Continuous improvement process is a tradition of method improvement focusing the elimination of waste in all systems and process in an organisation. Continuous improvement has been an important part of manufacturing ... -
The improvement of the production line of the assembly of audio product
(Universiti Malaysia Perlis (UniMAP), 2016-04)The main reason for low production rate of audio based products were inappropriate handling of assembly process. This study was conducted to reduce the product operating time. By using line-balancing process, this study ... -
The improvement on inventory system using lean-six sigma approache
(Universiti Malaysia Perlis (UniMAP), 2016-06)The inventory system is a quantity of goods product and was storing in warehouse by a business that is intended either for resale or as a raw materials and components used in producing goods that the business sells. This ... -
An improvement study of outgoing materials handling at Perodua Engine Manufacturing Sdn. Bhd. (PEMSB) Plant in Sg Choh Rawang, Selangor
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2009-05)An outgoing material handling improvement conducted in Perodua Engine Manufacturing Sdn. Bhd. (PEMSB) plant in Sg. Choh Rawang applies engineering theoretical knowledge into practice. Integration of both Toyota Production ... -
Improvement the design and development of corn removal machine
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)The project had examined the design and development of corn removal machine. Eating cooked sweet corn significantly boosts the grain’s health giving antioxidant activity, which can substantially reduce the chance of heart ... -
Improving throughput time on motorcycle engine assembly plant
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010)This research describes an approach that can improving throughput time on motorcycle manufacturing engine assembly plant. Nowadays, the motorcycle industries facing challenge on how to improve throughput time in engine ... -
Influence treatment time of lanthanum conversion coating on magnesium alloy
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)This final report consists of several key sections, which are: introduction, problem faced, method of solution, result, discussion and conclusion. Introduction of project described briefly about the material used that is ... -
Investigate mechanical properties of laminated flax fabric composite plate with different laminate code lamination
(Universiti Malaysia Perlis (UniMAP), 2016-06)This paper studied the mechanical behaviors of laminated flax fabric composite plate with different laminate code lamination. The aim of the study is to observe the influence of the different angle in the specimen either ... -
Investigate of usage of water as a blast mitigator for high impact penetrator
(Universiti Malaysia Perlis (UniMAP), 2015-12)This project is about investigating the usage of water as a blast mitigator for high impact penetrator. The high impact penetrator is an apparatus that uses to accelerate the projectile at high velocity. The shaped charge ... -
Investigate the effect of cutting parameter pn Ti6Al4V surface in EDM wire-cut
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)Titanium aloy is aprovide exellent corrosion resistance, a high strength-to-weight-ratio and good high temperature. It’s also have very high affinity to oxygen. A natural oxide layer is always present on the surface. A ... -
Investigation and design of an ergonomic Wheelchair Seat for Paraplegic
(Universiti Malaysia Perlis (UniMAP), 2016-06)The title of this project is Investigation and Design of an Ergonomic Wheelchair Seat for Paraplegic. The project has two main objectives, the first is to investigate the condition of the seating to be more ergonomic ... -
Investigation and design of vibration compensation for a wheelchair
(Universiti Malaysia Perlis (UniMAP), 2016-06)When traveling over uneven surfaces such as paved road and obstacles, wheelchairs experienced vibration that causes the body of the person who sit on the wheelchair to experienced whole body vibration. The effect of the ... -
Investigation new sensing SnTiO3 as thin film light sensor
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)In this project, some research has been done on Tin dioxide (SnO2) and stannium titanate perovskite (SnTiO3) thin films. It has been known that tin dioxide has various applications, especially for gas sensor, light sensor, ... -
Investigation of characteristics of powder at press surpasses 3000 ton
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project is carried out to investigate characteristic an iron powder at pressure beyond 3000 tons. The effects of high load and pressure on a compacted powder were investigated. A cube shape was produced using pressing ... -
Investigation of dimensional accuracy and chip formation on peck drilling of mild steel
(Universiti Malaysia Perlis (UniMAP), 2016-05)Drilling process is the most important machining process in the manufacturing industries. Almost all mild steel industries and production are based on drilling process. However, the difficulty of the mild steel machining ...