Now showing items 5-24 of 88

    • Characterization of F75-HAP produced by Powder Metallurgy method 

      Nur Maizatul Shima, Adzali; Shamsul Baharin, Jamaludin; Mohd Nazree, Derman; Nur Hidayah, Ahmad Zaidi (Universiti Malaysia Perlis, 2009-12-01)
      This research was carried out to study the properties of Co-Cr-Mo filled with different composition of HAP that have been prepared by powder metallurgy method. The raw materials used in this research were Co-Cr-Mo powder ...
    • Characterization of porous aluminum fabricated via sintering- dissolution process (SDP) 

      Shamsul Baharin,  Jamaludin, Prof. Dr.; Nik Mohd Fikry, Mohd Rushdi; Alida, Abdullah; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr. (Trans Tech Publications, 2013)
      Porous metals that have open pores structure with low density and light weight properties are suitable to be used in many engineering applications. In this work, the porous aluminum was fabricated via sintering dissolution ...
    • Cobalt Implant Composite (CIC) 

      Shamsul Baharin, Jamaludin, Prof. Dr.; Che Mohd. Ruzaidi, Ghazali, Prof. Madya; Nurhidayah, Ahmad Zaidi; Mazlee, Mohd. Noor (Ministry of Higher Education (MOHE), 2005-09-30)
      Cobalt implant composite (CIC) was fabricated in KUKUM by powder metallurgy technique.
    • Comparative characterization of Clinker’s microstructure at different temperature zone during cement production 

      Mohd Sobri, Idris; Khairul Nizar, Ismail; Shamsul Baharin, Jamaludin; Che Mohd Ruzaidi, Ghazali; Kamarudin, Hussin (Science Publications, 2007)
      Temperature is an important parameter for transformation of minerals in clinker during cement productions. It influences the formation of alite from belite during calcinations and clinkering processes. The result of ...
    • Comparative study of corrosion behavior of AA2014/15 Vol%Al2O3p and AA2009/20 Vol% SiCw 

      Shamsul Baharin, Jamaludin; Z. Yusoff; Khairel Rafezi, Ahmad (Portuguese Electrochemical Society, 2008)
      The influence of heat treatment on the corrosion behavior of two aluminium matrix composites (AA2014/15 vol% Al2O3p - composite A and AA2009/20 vol% SiCw - composite B) was analyzed in 3.5% sodium chloride solution. The ...
    • Comparative study on thermal, compressive, and wear properties of palm slag brake pad composite with other fillers 

      Che Mohd Ruzaidi, Ghazali, Assoc. Prof.; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr.; Shamsul, Baharin Jamaludin, Prof. Dr.; Mohd Mustafa Al Bakri, Abdullah (Trans Tech Publications, 2011)
      The attractive performance-to-cost ratio associated with the incorporation of waste material in composite formulations used to produce brake pads has stimulated the idea of exploring the possible incorporation of additional ...
    • Comparison of dynamic mechanical properties of non-superheated and superheated A357 alloys 

      Mazlee, Mohd. Noor; Shamsul Baharin, Jamaludin; Kamarudin, Hussin (Slovak Academy of Sciences, 2010-03-01)
      The influence of superheat treatment on the microstructure and dynamic mechanical properties of A357 alloys has been investigated. The study of microstructure was performed by optical microscope. Dynamic mechanical ...
    • Composite cement reinforced coconut fiber: physical and mechanical properties and fracture behavior 

      Alida, Abdullah; Mazlee, Mohd Noor, Dr.; Shamsul, Baharin Jamaludin, Prof. Dr.; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr. (INSInet Publications, 2011)
      This research paper reports the effect of natural fiber content on the physical and mechanical properties as well as fracture behavior of composite cement reinforced with coconut fiber. The mix design was based on 1:1 for ...
    • Compressive strength and crack propagation of cement composites reinforced coconut fibre 

      Alida, Abdullah; Shamsul Baharin, Jamaludin, Prof. Dr.; Mazlee, Mohd Noor; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr. (Medwell Journals, 2012)
      This study presents the compressive strength and crack propagation of cement composites reinforced coconut fibre. The development of cement composites in this research were done by substituting coconut fibre to the portion ...
    • The corrosion studies of powder metallurgy Co-Cr-Mo (F-75) alloy 

      Zuraidawani, Che Daud; Shamsul Baharin, Jamaludin, Prof. Dr.; Mohd Nazree, Derman, Dr.; Juyana, A Wahab          (AENSI Publisher All rights reserved, 2013-10)
      Co-Cr-Mo (F-75) alloy was investigated for biomedical application due to its mechanical properties and good corrosion resistance. This study has been focusing on the corrosion behavior of PM Co-Cr-Mo alloy. The Co-Cr-Mo ...
    • Development of a Lid Sealed furnace for the production of Magnesium alloys 

      Shaiful Rizam, Shamsudin; Azmi, Kamardin; Mohd Nazree, Derman; Shamsul Baharin, Jamaludin; Azremi, Abdullah Al Hadi; A.M.H. Firdaus; Mazlee, Mohd Noor; C.I. Mahdi; Abdul Razak, Daud; Roslinda, Shamsudin (Universiti Kebangsaan Malaysia (UKM), 2008-12-03)
      An atmosphere-controlled furnace was designed for the casting process of highly reactive Mg metal and its alloys. Instead of open crucible furnace, the melting process was done under controlled atmosphere which contained ...
    • The development of cement composites reinforced coconut fiber with fly ash addition: mechanical properties and fracture behaviour 

      Mazlee, Mohd Noor, Dr.; Shamsul, Baharin Jamaludin, Prof. Dr.; Nur Izzati, Muhd Nadzri (Trans Tech Publications, 2013)
      This research paper presents a study on the development of cement composites reinforced coconut fiber with fly ash addition. Various content of coconut fiber (3 wt. %, 6 wt. %, 9 wt. %, 12 wt. % and 15 wt. %) was added to ...
    • Development of coconut fiber with the addition of fly ash for cement panel application in construction 

      Alida, Abdullah; Shamsul Baharin, Jamaludin, Prof. Dr.; Mazlee, Mohd Noor (Universiti Malaysia Perlis (UniMAP)Centre for Graduate Studies, 2010-10-16)
      Natural fibers exist in large quantities and have been classified as waste materials. Coconut fiber is one of them and it is used as addition in fabrication of cement panel. Industrial waste materials such fly ash is ...
    • Development of dense hydroxyapatite-ni by modified electroless deposition technique. 

      Sri Asliza, Md Amin; Mohd Zaheruddin, Kasmuin; Azmi, Rahmat, Dr.; Shamsul Baharin, Jamaludin, Prof. Dr.; Khairel Rafezi, Ahmad, Dr. (Trans Tech Publications, 2014)
      Ni deposited on HA powder was prepared by electroless plating process without sensitization and activation treatment. The deposited powder obtained was characterized by energy dispersive spectroscopy (EDX) and x-ray ...
    • Dry sliding wear and compressive strength of Fe-Cr matrix composite with and without Al2O3 reinforcement 

      Shamsul, Baharin Jamaludin, Prof. Dr.; Saidatulakmar, Shamsuddin; Zuhailawati, Hussain; Zainal Arifin, Ahmad (IEEE Conference Publications, 2011)
      Fe-Cr matrix composites reinforced with Al2O3 particulates fabricated by powder metallurgy (PM) method offer potential for cheaper wear resistance materials and high temperature application. The influence of Al2O3 amount ...
    • Effect of alloying elements (Ni and Cr) on density and hardness of Co alloy fabricated by powder metallurgy 

      Raudhah, Othman; Shamsul Baharin, Jamaludin; Mohd Nazree, Derman (Universiti Malaysia Perlisp.1-5, 2009-12-01)
      Influences of Ni and Cr addition on the properties of powder metallurgy Co base alloys were investigated. The alloys were produced by powder metallurgy technique and sintered under argon atmosphere. Scanning electron ...
    • Effect of beta tricalcium phosphate (β-TCP) on properties of Mg-Zn composites 

      Siti Aisyah, Buyong; Shamsul Baharin, Jamaludin, Prof. Dr.; Rohaya, Abdul Malek (Trans Tech Publications, 2014)
      In this work, Mg and Zn powder were used to prepare the Mg-Zn/β-TCP composites with different β-TCP composition by using powder metallurgy technique. The composite were mixed using ball mill and compacted at 500 MPa. The ...
    • Effect of Colloidal SIO2 Content on the Morphology of Coated Ceramic Particles 

      Shaiful Rizam Shamsudin; Mazlee Mohd Noor; Shamsul Baharin Jamaludin, Assoc. Prof. Dr.; Mohd Fitri Mohamad Wahid; Ruhiyuddin Mohd Zaki; Khairel Rafezi Ahmad; A.G.B. Syamsul; M. Harun; Y. Hafizal (Universiti Malaysia Perlis (UniMAP), 2007-06-09)
      Coated structure on fly ash particles was produced by liquid stirring of colloidal SiO2. Morphological study by means of scanning electron microscope has consent to controlling the present of outer layer by the addition ...
    • Effect of different nickel content on the mechanical properties of hydroxyapatite-ni composites from coated powders 

      Sri Asliza, Md Amin; Mohd Zaheruddin, Kasmuin; Azmi, Rahmat, Dr.; Shamsul Baharin, Jamaludin, Prof. Dr.; Khairel Rafezi, Ahmad, Dr. (Trans Tech Publications, 2014)
      HA-Ni composites were fabricated by uniaxial pressing from coated powders, in which HA particles were successfully coated with nickel precursor by the electroless deposition method. The compacted powders sintered at ...
    • The effect of heat treatment on the anode efficiency of Magnesium sacrificial anode 

      A.M.H., Firdaus; Saiful Rizam, Shamsudin; Shamsul Baharin, Jamaludin; Mohd Nazree, Derman (Universiti Malaysia Perlis, 2009-12-01)
      High efficiency sacrificial anode from Mg alloy is needed as it has higher capability of protecting underground metal structure against corrosion in cathodic protection. Solution treatment was applied to Mg sacrificial ...