Browsing School of Manufacturing Engineering (Articles) by Title
Now showing items 1-20 of 125
-
Aerodynamic study of combustor using axial swirler
(Praise Worthy Prize S.r.l., 2011-01)A study has been conducted to investigate the flow pattern in a gas turbine combustion chamber by simulation and experimental approaches. Flow pattern inside a combustor is important to self sustain the flame, increase ... -
Algorithm to improve process robustness in the assembly & test manufacturing industry a case study of the 1064nm wavelength laser mark equipment
(Trans Tech Publications, 2013-09)This document explains and demonstrates the generic improvement algorithm created to enhance the maintenance methodology in the semiconductor manufacturing environment. The use of this algorithm demonstrates how a process ... -
Analysis of buffered assembly line productivity
(Emerald Group Publishing Limited, 2014)Purpose – The paper aims to study car assembly line, to show its productivity rate, and to derive a mathematical model for the productivity rate of the assembly line segmented into sections with embedded buffers. Design ... -
Analysis of part jamming in a feeder of automatic machines
(Emerald Group Publishing Limited, 2011)Purpose - The purpose of this paper is to present an analysis and practical study of part jamming in the feeder of an automatic machine. Design/methodology/approach - The reliability of the feeder is derived by the probability ... -
Analyzing the jamming of parts on the shaft in assembly processes
(Emerald Group Publishing Limited., 2012)Purpose - The purpose of this paper is to investigate the process of jamming of the hollow parts on the shaft and to derive a mathematical model for jamming in an assembly process. Design/methodology/approach - The ... -
Anthropometry data for 4th year UniMAP student
(Universiti Malaysia Perlis (UniMAP), 2009-12-01)Anthropometry is a science of measurements and the art of application that establishes the physical geometry, mass properties, and strength capabilities of the human bodies. This paper was taken out from laboratory session ... -
Application of Chemical Health Risk Assessment (CHRA) in an industry
(Universiti Malaysia Perlis (UniMAP), 2009-12-01)Occupational Safety and Health (Use and Standards of Exposure of Chemicals Hazardous to Health) Regulation 2000 requires Chemical Health Risk Assessment (CHRA) to be carried out at all work places where chemical been ... -
Application of Statistical Design of Experiment (SDE) to study wrinkles and delamination defects on composite sandwich panels
(2007)The sandwich panels made of composite materials are subject to a variety of process parameters. In this paper an experimental investigation of composite manufacturing significant issues; such as wrinkles and delamination ... -
Applications of HIRARC at UniMAP Laboratories
(Universiti Malaysia Perlis (UniMAP), 2009-12-01)As a technical university which hands on practices are common to students, Universiti Malaysia Perlis (UniMAP) accommodates numbers of laboratories. From the basic fundamentals to the high-end laboratories, there might be ... -
Asymmetric error control for production systems in mechatronics
(2000)In the realm of E-manufacturing, the job tool movements should be precisely controlled which normally involve the directions East-West and South-North. Whereas the robot applications often involve either obstacle detection ... -
Catalytic combustion system for use in Malaysia small gas turbine: A feasibility study
(Praise Worthy Prize S.r.l., 2011-01)Nowadays, the rates of air pollutant produced by small gas turbine in manufacturing and automobile industries increased continuously. Besides that, the uncontrolled rate of emissions released into the ambient air could ... -
Characteristic and corrosion studies of rare earth (REE) based anodizing on AZ91D magnesium alloy
(Trans Tech Publications, 2014-01)Oxide coatings on AZ91D magnesium alloy were prepared using anodizing technique with 10mA/cm2 current density for 5 minutes in electrolyte containing Mg (NO₃)₂ with NaVO₃ as an additive. The corrosion behaviors of different ... -
Characteristics of Fe-yttria composites fabricated by powder metallurgy method
(Trans Tech Publications, 2013)This study is focused on fabricating and characterizing iron (Fe) composites prepared by powder metallurgy route reinforced with varying weight of Yttria (Y2O3). Composites were prepared based on 5 wt. % to 15 wt. % of ... -
Characterization of PM Fe-Cr-Y₂O₃ composites prepared by microwave sintering technology
(Trans Tech Publications, 2014-01)This research is focused on assessing the feasibility of the new and innovative microwave sintering technology for fabricating iron-chromium composites prepared via powder metallurgy route. Accordingly, the microwave ... -
Chip formation studies in machining fibre reinforced polymer composites
(Inderscience Enterprises Ltd., 2013)The use of end milling process for machining of fibre reinforced polymer composites has been widespread in various industries. Until recently, very little work has been reported with regard to characterisation of chip ... -
Classroom comfort ability assessment: A case study
(Praise Worthy Prize S.r.l., 2012-03)his study was conducted to evaluate the comfort level of an air-conditioned classroom at the School of Manufacturing Engineering campus using objective measurement, subjective assessment and Computational Fluid Dynamics ... -
Combustor aerodynamic using radial swirler
(Academic Journals, 2011-07)A study has been conducted to investigate the flow pattern in a gas turbine combustion chamber by simulation and experimental approaches. Flow pattern inside a combustor is important to self sustain the flame, increase ... -
Comparison between ANSYS and CATIA simulation capability in simulating round shape diaphragm of MEMS piezoresistive pressure sensor
(Institute of Electrical and Electronics Engineering (IEEE), 2007-11)This paper presents a comparative study of MEMS Piezoresistive Pressure Sensor simulation using two different software of ANSYS and CATIA respectively. It is aimed to investigate the feasibility of utilizing CATIA software ... -
Comparison between single and multi gates for minimization of warpage using taguchi method in injection molding process for ABS material
(Trans Tech Publications, 2013-12)In this study, a mold is designed in single and dual type of gate in order to investigate the deflection of warpage for thick component in injection molding process. Autodesk Moldflow Insight software was used as a medium ...