Collections in this community

Recent Submissions

  • The impact of working gas on heat transfer performance of tube banks heat exchanger in a thermoacoustic system 

    Lin, Chou Aw; Fatimah Al Zahrah, Mohd Saat; Fadhliah, Shikh Anuar; Mohamad Firdaus, Sukri; Mohd Zaid, Akop; Saechan, Patcharin (Universiti Malaysia Perlis (UniMAP), 2022-03)
    Thermoacoustic system is a system introduced as an alternative technology for refrigerators or heat engine because it uses environmentally friendly gases as a working medium. Thermoacoustic system usually uses noble ...
  • The effect of porous materials on temperature drop in a standing wave thermoacoustic cooler 

    Nur Damia Asma, Rosle; Fatimah Al Zahrah, Mohd Saat; Raja Nor Firdaus Kashfi, Raja Othman; Mohamad Firdaus, Sukri; Saechan, Patcharin (Universiti Malaysia Perlis (UniMAP), 2022-03)
    Thermoacoustics is a principle of sciences that offers an alternative solution for cooling system with a technology that is green and sustainable. The thermoacoustic energy conversion takes place mostly within the area of ...
  • Effect of light intensity on indoor temperature and air velocity: a simulation study 

    Shehab, S.; M. Zaid, Akop; N. A., Masripan; A. H., Nurfaizey; F., Wasbari; A. A., Saad; M. R., Mansor; A., Noordin; S. G., Herawan (Universiti Malaysia Perlis (UniMAP), 2022-03)
    It is essential to understand the factors influencing thermal responses to improve human comfort and properly reduce energy consumption. It has been confirmed that parameters unrelated to the thermal environment can ...
  • Numerical analysis of GNP/Ag Die-Attach adhesives with different thermal conductivity 

    Ameeruz Kamal, Ab Wahid; Mohd Azli, Salim; Nor Azmmi, Masripan; Chonlatee, Photong; Adzni, Md. Saad; Mohd Zaid, Akop; Muhd Ridzuan, Mansor (Universiti Malaysia Perlis (UniMAP), 2022-03)
    The thermal conductivities of a multilayer model of GNP/Ag hybrid die-attach material are explored using steady-state thermal modeling. The heat flux in multilayer GNP/Ag hybrid structures is shown to be highly layer ...
  • Parametric analysis of sound transmission loss in a rectangular duct attached with resonator silencer 

    Muhammad, Mohamed Salleh; Mohd Hafiz, Ghazali; Salihatun, Md Salleh; Bukhari, Manshoor; Amir, Khalid; Chan, Shiau Wei; Izzuddin, Zaman (Universiti Malaysia Perlis (UniMAP), 2022-03)
    Noise is an existing problem that exist in the environments produced from vibrating sources. In general, the common solutions for noise control are: (1) redesigning the system the system for instance increasing wall ...
  • Electroencephalogram (EEG)-based systems to monitor driver fatigue: a review 

    Muhammad Shafiq, Ibrahim; Seri Rahayu, Kamat; Syamimi, Shamsuddin (Universiti Malaysia Perlis (UniMAP), 2022-03)
    An efficient system that is capable to detect driver fatigue is urgently needed to help avoid road crashes. Recently, there has been an increase of interest in the application of electroencephalogram (EEG) to detect ...
  • Synthesis of a self-reeling hose system for bathroom use 

    Hui, Lin See; Zairulazha, Zainal; Shamsul Anuar, Shamsudin; Huthaifa Ahmad, Al_Issa (Universiti Malaysia Perlis (UniMAP), 2022-03)
    This work was carried out to design and test the self-reeling hose for bathroom use to achieve convenience and hygiene in the bathroom. The distribution of von Mises stress, displacement and safety factors were considered. ...
  • The impact of alkaline treatment on the mechanical and physical properties of Kenaf core fibre reinforced vinyl ester composites 

    Aida, H. J.; Nadlene, R.; Mastura, M. T.; Noryani, M.; S. M. Fadzullah, S. H.; Kamrolzaman, A. A.; Salim, M. A.; Bushra, Rashid (Universiti Malaysia Perlis (UniMAP), 2022-03)
    Nowadays, natural fibre has a high demand in any application development. The use of natural fibre in various applications worldwide is one of the alternative ways to replace synthetic fibre. Currently, polymer composites ...
  • Simulation-based assembly line balancing and manpower allocation in a cellular manufacturing system 

    Rohana, Abdullah; M. N., Abd Rahman; A. H., Abdul Rasib; M. I. H., C. Abdullah; H. O., Mansoor (Universiti Malaysia Perlis (UniMAP), 2022-03)
    A well-balanced manufacturing system is key for ensuring a smooth production flow and the most efficient use of manpower and equipment This study aims to improve the cellular manufacturing system’s assembly line balance ...
  • A study on heavy vehicle visibility and crash analysis using ANSYS 

    Uvaaraj, Jagatheesvaran; Shamsul Anuar, Shamsudin; Norasra, A. Rahman; Syed Najib, Syed Salim; Shahrudin, Zakaria; Zairulazha, Zainal; Safarudin Gazali, Herawan; Huthaifa Ahmad, Al_Issa (Universiti Malaysia Perlis (UniMAP), 2022-03)
    A pilot study was conducted to evaluate the visibility of heavy truck in Malaysia. A survey, analytical computations, and computer simulations were all part of the investigation scope. The survey was conducted with 40 ...
  • Simulation study on structure bumper beam using finite element analysis 

    Hambali, A.; Kasim, M. S.; Husshini, N. H. N.; Muhammad Nasiruddin, S.; MAM Nawi; Rosidah, J.; Mohamed, S. B.; Ito, Teruaki (Universiti Malaysia Perlis (UniMAP), 2022-03)
    One of the main parts of the automotive bumper system is the bumper beam. A bumper beam is a safety feature of a car where it functions to absorb impact energy during a collision. It is important to improve the bumper ...
  • Effect of abrasive water jet turning AWJT parameter setting on surface finish of Inconel 718 

    Kasim, M. S.; Kasman, Z.; Jefri, A. S.; Mohamad, W. N. F.; Hambali, A.; Hafiz; M. S. A., Husshini; N. H. N., Mohamed, S. B; Izamshah, R.; Ito, T. (Universiti Malaysia Perlis (UniMAP), 2022-03)
    This research article aims at comparing the cutting performance of Inconel 718 during abrasive waterjet turning (AWJT). In this study, the various combination processing parameters were performed namely; depth of cut (DOC), ...
  • Effect of water content on correlation of biomechanical properties and grayscale of articular cartilage using Low-Field MRI 

    F. A. S., Hamshary; M. J., Abd Latif; M. S., Zakaria; M. N., Harun; J., Mahmud; Nguyen, H. Q. (Universiti Malaysia Perlis (UniMAP), 2022-03)
    The early assessment of osteoarthritis is very crucial since articular cartilage has a very limited ability to regenerate and self-repair as the degeneration happened. Thus, MRI is the most important imaging modality for ...
  • Evaluation of the Banana slicing machine structure design 

    Mahmod Abd Hakim, Mohamad; Yahaya, Ramli; Mohd Afiq Danial, Khairull Azhar; Abd Khalil, Abd Rahim; Khairul Anuar, Abd Wahid; Mohd Shahir, Yahya; W. Sani (Universiti Malaysia Perlis (UniMAP), 2022-03)
    In the product planning procedure of a machine tool, mature designers consider various kinds of customers’ requirements, while simultaneously conducting the necessary information processing, so as to finally determine ...
  • Parameter optimization of fused deposition modeling process for 3D printed prosthetic socket using PCR-TOPSIS method 

    Lim, G. D.; M. J., Abd Latif; M. R., Alkahari; M. S., Yob; M., Musa; M. N., Abdul Rahman; P., Rajaandra; Nguyen, H. Q. (Universiti Malaysia Perlis (UniMAP), 2022-03)
    Prosthetic socket plays the most important role in lower limb prosthesis. The conventional fabrication process of prosthetic socket is labor intensive and time-consuming. The application of additive manufacturing technology ...
  • Unmanned aerial vehicle technology use in visual road inspection at Ft005, Johor Bahru-Melaka 

    Masiri, Kaamin; Saiful Azhar, Ahmad Tajudin; Nor Athirah, Basri; Rosdi, Ab Rahman; Ahmad Hakimi, Mat Nor; Muhammad Azraie, Abdul Kadir; Mardiha, Mokhtar; Luo, Pingping (Universiti Malaysia Perlis (UniMAP), 2022-03)
    Visual road inspection is one of the key phases of road maintenance to examine and describe the condition of road infrastructure. The local authority still uses the conventional road inspection method. However, this ...
  • Waste mussel shells as an adsorbent for Phosphate removal in solution: kinetic and isotherm model 

    Noorul Hudai, Abdullah; Slyvester Layang, Liom; Adam Haqiem, Zainudin; Muhammad Afiq Irfan, Huzil; Mohamad Syahrul Syazwan, Yaacob; Nur Atikah, Abdul Salim; Masiri, Kaamin; Amirreza, Talaiekhozani (Universiti Malaysia Perlis (UniMAP), 2022-03)
    Eutrophication occurs when there is excess nutrient, such as phosphates, in water bodies. It causes algae bloom, which in turn disrupts aquatic life. In this study, low-cost waste mussel shell was applied as adsorbent ...
  • Prediction of coastal erosion/accretion and sediment properties at Batu Pahat coastal area 

    Mardiha, Mokhtar; Mohd Effendi, Daud; Masiri, Kaamin; Nor Baizura, Hamid; Mohamad Azim, Mohammad Azmi; Nur Ellena, Solikhin; Duong, Nguyen Anh (Universiti Malaysia Perlis (UniMAP), 2022-03)
    Coastal erosion and accretion may be defined to be natural processes for which predicting the coastal magnitude is essential for a better coastal monitoring. The purpose of this study is to investigate the shoreline ...
  • Investigation of Pantai Punggur coastal erosion by using UAV Photogrammetry 

    Mohammad Ikhmal, Siddiq; Mohd Effendi, Daud; Masiri, Kaamin; Mardiha, Mokhtar; Amin Shah, Omar; Anh Duong, Nguyen (Universiti Malaysia Perlis (UniMAP), 2022-03)
    The shoreline is the line that marks the boundary between water and land. Monitoring and analysing shoreline changes is critical because it provides a greater understanding of the shoreline changes as well as the ...
  • Evaluation of Orthophoto image using UAV Photogrammetry in UTHM Parit Raja 

    Masiri, Kaamin; Nuranis, Amera; Muhammad Syakir, Subli; Nur Hidayah, Azhar; Suhaila, Sahat; Norhayati, Ngadiman; Nur’ain, Idris; Amirreza, Talaiekhozan (Universiti Malaysia Perlis (UniMAP), 2022-03)
    A map is highly vital to enable individuals to maneuver between places. It also provides a tool to estimate, characterize, or describe an area. Google Earth is the most recent technology used to help individuals navigate ...

View more