• Design and electrical simulation of a 22nm MOSFET with graphene bilayer channel using Double High-ĸ Metal Gate 

  Izwanizam, Yahaya; F., Salehuddin; K. E., Kaharudin (Universiti Malaysia Perlis (UniMAP), 2022-04)

  This paper will discuss the virtual fabrication design process of a 22nm MOSFET bilayer graphene with high-ĸ metal gate (HKMG). Silvaco software's TCAD fabrication tools were utilized, with the Athena simulation module ...

• Supercapacitor performance with activated carbon and graphene aerogel composite electrodes 

  Abdul Hakim, Ab. Rahim; Anis Nurashikin, Nordin; Mohd. Firdaus, Abd. Wahab (Universiti Malaysia Perlis (UniMAP), 2022-04)

  Thus far, activated carbon (AC) has been the material of choice as practical supercapacitor electrode material. However, graphene can be a better alternative material. This work presents a comprehensive ratio study of AC ...

• Reduction of electrical stresses in grid micro inverter through semiconductor switches 

  Sheeraz, Ahmed; Shayan, Tariq; Asif, Nawaz; Shahid, Latif; Atif, Ishtiaq (Universiti Malaysia Perlis (UniMAP), 2022-04)

  Micro inverters are power electronics devices integrated close to photovoltaic (PV) panels. PVs produced today could make 92% of its rated power. With the passage of time, the reliability and performance of micro inverter ...

• Improvement of the cement mortar properties using recycled waste materials 

  Manal Hamed Jasem (Universiti Malaysia Perlis (UniMAP), 2022-04)

  Ceramic tiles as well as brick waste materials from building demolition and black tea waste have caused major environmental issues. As a result, one of the primary objectives of sustainable solid waste management is ...

• Experimental and numerical flexural analysis of porous functionally graded beams reinforced by (Al/Al2O3) nanoparticles 

  Sadeq H. Bakhy; Muhannad Al-Waily (Universiti Malaysia Perlis (UniMAP), 2022-04)

  The porosity distribution, which varies through-thickness direction, plays a vital role in affecting the microstructure and mechanical properties of the final product. This study develops numerical and experimental techniques ...

• Optical investigations of GaN deposited nano films using pulsed laser ablation in ethanol 

  Husam Aldin A. Abdul Amir; Ali. A.Alwahib (Universiti Malaysia Perlis (UniMAP), 2022-04)

  We provide an optical study on GaN thin film testing created by pulsed laser (ablation) in liquid. This study applied six different energies for ablated GaN nanoparticles in the liquid. According to the XRD test, the ...

• The impact of working gas on heat transfer performance of tube banks heat exchanger in a thermoacoustic system 

  Lin, Chou Aw; Fatimah Al Zahrah, Mohd Saat; Fadhliah, Shikh Anuar; Mohamad Firdaus, Sukri; Mohd Zaid, Akop; Saechan, Patcharin (Universiti Malaysia Perlis (UniMAP), 2022-03)

  Thermoacoustic system is a system introduced as an alternative technology for refrigerators or heat engine because it uses environmentally friendly gases as a working medium. Thermoacoustic system usually uses noble ...

• The effect of porous materials on temperature drop in a standing wave thermoacoustic cooler 

  Nur Damia Asma, Rosle; Fatimah Al Zahrah, Mohd Saat; Raja Nor Firdaus Kashfi, Raja Othman; Mohamad Firdaus, Sukri; Saechan, Patcharin (Universiti Malaysia Perlis (UniMAP), 2022-03)

  Thermoacoustics is a principle of sciences that offers an alternative solution for cooling system with a technology that is green and sustainable. The thermoacoustic energy conversion takes place mostly within the area of ...

• Effect of light intensity on indoor temperature and air velocity: a simulation study 

  Shehab, S.; M. Zaid, Akop; N. A., Masripan; A. H., Nurfaizey; F., Wasbari; A. A., Saad; M. R., Mansor; A., Noordin; S. G., Herawan (Universiti Malaysia Perlis (UniMAP), 2022-03)

  It is essential to understand the factors influencing thermal responses to improve human comfort and properly reduce energy consumption. It has been confirmed that parameters unrelated to the thermal environment can ...

• Numerical analysis of GNP/Ag Die-Attach adhesives with different thermal conductivity 

  Ameeruz Kamal, Ab Wahid; Mohd Azli, Salim; Nor Azmmi, Masripan; Chonlatee, Photong; Adzni, Md. Saad; Mohd Zaid, Akop; Muhd Ridzuan, Mansor (Universiti Malaysia Perlis (UniMAP), 2022-03)

  The thermal conductivities of a multilayer model of GNP/Ag hybrid die-attach material are explored using steady-state thermal modeling. The heat flux in multilayer GNP/Ag hybrid structures is shown to be highly layer ...

• Parametric analysis of sound transmission loss in a rectangular duct attached with resonator silencer 

  Muhammad, Mohamed Salleh; Mohd Hafiz, Ghazali; Salihatun, Md Salleh; Bukhari, Manshoor; Amir, Khalid; Chan, Shiau Wei; Izzuddin, Zaman (Universiti Malaysia Perlis (UniMAP), 2022-03)

  Noise is an existing problem that exist in the environments produced from vibrating sources. In general, the common solutions for noise control are: (1) redesigning the system the system for instance increasing wall ...

• Electroencephalogram (EEG)-based systems to monitor driver fatigue: a review 

  Muhammad Shafiq, Ibrahim; Seri Rahayu, Kamat; Syamimi, Shamsuddin (Universiti Malaysia Perlis (UniMAP), 2022-03)

  An efficient system that is capable to detect driver fatigue is urgently needed to help avoid road crashes. Recently, there has been an increase of interest in the application of electroencephalogram (EEG) to detect ...

• Synthesis of a self-reeling hose system for bathroom use 

  Hui, Lin See; Zairulazha, Zainal; Shamsul Anuar, Shamsudin; Huthaifa Ahmad, Al_Issa (Universiti Malaysia Perlis (UniMAP), 2022-03)

  This work was carried out to design and test the self-reeling hose for bathroom use to achieve convenience and hygiene in the bathroom. The distribution of von Mises stress, displacement and safety factors were considered. ...

• The impact of alkaline treatment on the mechanical and physical properties of Kenaf core fibre reinforced vinyl ester composites 

  Aida, H. J.; Nadlene, R.; Mastura, M. T.; Noryani, M.; S. M. Fadzullah, S. H.; Kamrolzaman, A. A.; Salim, M. A.; Bushra, Rashid (Universiti Malaysia Perlis (UniMAP), 2022-03)

  Nowadays, natural fibre has a high demand in any application development. The use of natural fibre in various applications worldwide is one of the alternative ways to replace synthetic fibre. Currently, polymer composites ...

• Simulation-based assembly line balancing and manpower allocation in a cellular manufacturing system 

  Rohana, Abdullah; M. N., Abd Rahman; A. H., Abdul Rasib; M. I. H., C. Abdullah; H. O., Mansoor (Universiti Malaysia Perlis (UniMAP), 2022-03)

  A well-balanced manufacturing system is key for ensuring a smooth production flow and the most efficient use of manpower and equipment This study aims to improve the cellular manufacturing system’s assembly line balance ...

• A study on heavy vehicle visibility and crash analysis using ANSYS 

  Uvaaraj, Jagatheesvaran; Shamsul Anuar, Shamsudin; Norasra, A. Rahman; Syed Najib, Syed Salim; Shahrudin, Zakaria; Zairulazha, Zainal; Safarudin Gazali, Herawan; Huthaifa Ahmad, Al_Issa (Universiti Malaysia Perlis (UniMAP), 2022-03)

  A pilot study was conducted to evaluate the visibility of heavy truck in Malaysia. A survey, analytical computations, and computer simulations were all part of the investigation scope. The survey was conducted with 40 ...

• Simulation study on structure bumper beam using finite element analysis 

  Hambali, A.; Kasim, M. S.; Husshini, N. H. N.; Muhammad Nasiruddin, S.; MAM Nawi; Rosidah, J.; Mohamed, S. B.; Ito, Teruaki (Universiti Malaysia Perlis (UniMAP), 2022-03)

  One of the main parts of the automotive bumper system is the bumper beam. A bumper beam is a safety feature of a car where it functions to absorb impact energy during a collision. It is important to improve the bumper ...

• Effect of abrasive water jet turning AWJT parameter setting on surface finish of Inconel 718 

  Kasim, M. S.; Kasman, Z.; Jefri, A. S.; Mohamad, W. N. F.; Hambali, A.; Hafiz; M. S. A., Husshini; N. H. N., Mohamed, S. B; Izamshah, R.; Ito, T. (Universiti Malaysia Perlis (UniMAP), 2022-03)

  This research article aims at comparing the cutting performance of Inconel 718 during abrasive waterjet turning (AWJT). In this study, the various combination processing parameters were performed namely; depth of cut (DOC), ...

• Effect of water content on correlation of biomechanical properties and grayscale of articular cartilage using Low-Field MRI 

  F. A. S., Hamshary; M. J., Abd Latif; M. S., Zakaria; M. N., Harun; J., Mahmud; Nguyen, H. Q. (Universiti Malaysia Perlis (UniMAP), 2022-03)

  The early assessment of osteoarthritis is very crucial since articular cartilage has a very limited ability to regenerate and self-repair as the degeneration happened. Thus, MRI is the most important imaging modality for ...

• Evaluation of the Banana slicing machine structure design 

  Mahmod Abd Hakim, Mohamad; Yahaya, Ramli; Mohd Afiq Danial, Khairull Azhar; Abd Khalil, Abd Rahim; Khairul Anuar, Abd Wahid; Mohd Shahir, Yahya; W. Sani (Universiti Malaysia Perlis (UniMAP), 2022-03)

  In the product planning procedure of a machine tool, mature designers consider various kinds of customers’ requirements, while simultaneously conducting the necessary information processing, so as to finally determine ...

View more