School of Materials Engineering (FYP)
Browse by

Full text contents of this collection is only available online for UniMAP communities
Recent Submissions
-
Implication of post cure temperature to molded Polyurethane/ Calcium Carbonate foam
(Universiti Malaysia Perlis (UniMAP), 2017-06)Implication of post cure temperature to molded polyurethane foam/calcium carbonate foam was investigated. The polyurethane foam samples were prepared by few steps which was mixing, stirring, curing and post curing into ... -
The effect of ENR as compatibilizer in Epoxy/NR/Graphene in conductive materials
(Universiti Malaysia Perlis (UniMAP), 2017-06)Graphene incorporated with epoxy composite was prepared using mechanical mixing technique with the density, flexural, fracture toughness, electrical conductivity and SEM morphology of the composite were studied. We chose ... -
The influence of co-precipitation and green synthesis of holy basil leaves, blue pea, and oolong tea on the properties of iron oxide nanoparticles
(Universiti Malaysia Perlis (UniMAP), 2017-06)Iron oxide nanoparticles (IONPs) are classified according to their size between 1 and 100 nanometers. In this study, IONPs were synthesized by two methods, conventional method which is co-precipitation and green synthesis ... -
Preparation of Ag/TiO₂ thin film by sol-gel method for solar panel application
(Universiti Malaysia Perlis (UniMAP), 2017-06)This research finding was about preparation of Ag/TiO₂ thin fllm by using sol-gel method. Three different parameter was used in this research by using pure titanium, 0.5g of doped silver and 1.0g of dopes silver that coated ... -
A study on electroless deposition of nickel onto hydroxyapatite
(Universiti Malaysia Perlis (UniMAP), 2017-04)In this study, it will be focused on the electroless deposition and concentration of nickel onto hydroxyapatite. This project shows the combining of hydroxyapatite and nickel by the difference weight of percentages. The ... -
The effect of Nano-Co-Ha onto sintering temperature
(Universiti Malaysia Perlis (UniMAP), 2017-06)The material use in this project was nano-Co-HA. The materials were prepared by process of electroless deposition and powder metallurgy to produce nano-Co-HA. Nano- Co-HA and HA were compacted by 20 tons shop press into ... -
Mechanical properties of Polyurethane / MWCNTs foam sandwich composites
(Universiti Malaysia Perlis (UniMAP), 2017-06)This study describes the effect of multi-walled carbon nanotubes (MWCNTs) on the properties, particularly modulus properties of rigid polyurethane (PU) foam produced from palm oil polyol (POP) and methylene diphenyl ... -
Influence of grain size on the isothermal oxidation of Fe-33Ni-19Cr alloy
(Universiti Malaysia Perlis (UniMAP), 2017-06)This research focuses on the influence of grain size on isothermal oxidation of the alloy Fe-19Cr-33Ni. Alloy Fe-19Cr-33Ni have been cut to the desired size and have been grind using a variety of grit sandpaper and weighed ... -
The effect of nickel plating on Mg alloy
(Universiti Malaysia Perlis (UniMAP), 2017-06)Magnesium (Mg) alloys absolutely have potential applications of engineering light materials which recently they have acquired abundant of attention due to their low weights. Weight reduction is strongly demand toward ... -
Optimization of resistance spot welding process parameter on quenched steel by Taguchi methods
(Universiti Malaysia Perlis (UniMAP), 2017-06)The optimization of resistance spot welding process parameter on quenched mild steel by Taguchi method is the main focuses in this research. Firstly, the parameter that being controlled are welding current, welding time ... -
Tensile shear strength and dynamic mechanical analysis of 6063 aluminium alloy and 304 stainless steel sheet by spot welding
(Universiti Malaysia Perlis (UniMAP), 2017-06)Mechanical properties of dissimilar metal of spot welding were tested and analyzed with different parameters which were welding current and welding time. From visual observation, the largest weld nugget recorded was 7.43 ... -
The fabrication of heparin imprinted fiber membrane using electrospinning
(Universiti Malaysia Perlis (UniMAP), 2016-06)The studies of the fabrication of Heparin Imprinted Fiber membrane using Electrospinning was presented and investigated. This studies is about electrospinning method use to produce membrane from Polyvinylidene fluoride ... -
Lightweight material based on fly ash geopolymer
(Universiti Malaysia Perlis (UniMAP), 2016-05)The utilization of fly ash in geopolymer concrete as an alternative to Ordinary Portland Cement partial replacement of cement gaining immerse importance today, mainly account of improvement in long term durability of ... -
Preparation and characterization of epoxy modified with palm oil based Polyol (POBP) with different curing systems
(Universiti Malaysia Perlis (UniMAP), 2016-06)This research concentrates on preparation and characterization of epoxy modified with palm oil based polyol (POBP) with different curing systems. The effect of POBP is investigated with ten ratios of epoxy samples with two ... -
Silica extraction from agricultural waste as corrosion inhibitor
(Universiti Malaysia Perlis (UniMAP), 2016-06)Rice husk and rice straw are found abundant as by-product of the the rice milling industry. Both of the agricultural wastes have a great potential to be used as raw material in industry. Rice husk and rice straw normally ... -
The use of solvents in epoxy/graphene conductive materials
(Universiti Malaysia Perlis (UniMAP), 2017-06)The influences of graphene nanofiller on physical, electrical and mechanical properties of epoxy composite were investigated. Epoxy was loaded with different content of graphene 0, 0.2, 0.4, 0.6, 0.8 and 1.0 vol% via ... -
Synthesis and characterization of Cobalt/Calcium Carbonate catalyst in the production of carbon nanotubes
(Universiti Malaysia Perlis (UniMAP), 2017-06)Since its discovery, carbon nanotubes (CNTs) have been widely researched owing to their large potential in nanotechnological applications. The effects of catalyst calcination behavior (temperature and duration) on the ... -
Effect of Zinc additions on Sn-0.7Cu-0.05Ni lead free solder alloy
(Universiti Malaysia Perlis (UniMAP), 2017-06)This project is focusing on the effect of zinc additions on Sn-0.7Cu-0.05Ni lead free solder alloy. The additional of micro-alloying have been developed by using casting technique with different percentage of zinc which ... -
Effect of Citric acid on properties of Cassava starch foam
(Universiti Malaysia Perlis (UniMAP), 2017-06)The effects of citric acid towards the properties of cassava starch foam was studied in this thesis. The influences of crosslinking on cassava starch was described fundamentally. This include the formation of cell sizes, ... -
The Effect of Granulated Blast Furnace Slag (GBFS) Composition on Geopolymer Paste Properties
(Universiti Malaysia Perlis (UniMAP), 2017)For the research study, I will perform the effect of Granulated Blast Furnace Slag (GBFS) composition on geopolymer paste properties. For my final year project, I will use raw materials of slag and fly ash that was provided ...