School of Manufacturing Engineering (FYP): Recent submissions
Now showing items 61-80 of 336
-
On study on heat flux variation due to temperature, humidity and ventilation flow of a model house for a certain continuous period
(Universiti Malaysia Perlis (UniMAP), 2016-05)The aim of this study was to understand and establish passive cooling method in hot humid climates. This is because Malaysia received high temperature with low air velocity that can influence the thermal comfort. The review ... -
Analysis of strength on the thick plate part using response surface methodology
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project is about research on the analysis of strength on the thick plate part (thickness of the part is more than 3mm) using Response Surface Methodology (RSM). The objective of this project is to improve the ... -
Thick plate part using genetic algorithm methodology
(Universiti Malaysia Perlis (UniMAP), 2016-06)This study focuses on the optimisation of the injection moulding parameters to maximise the strength on the moulded parts produced using Autodesk Moldflow Insight (AMI) 2012. The strength of the moulded parts moulded ... -
Study of heat transfer characteristics of Al2O3 nanoparticles in heat pipes
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project deals with the study of heat transfer characteristics of aluminium oxide nanoparticles in heat pipe. A heat pipe is a simple heat transfer device that can transfer large amount of heat from the evaporator ... -
Study of surface roughness during droplet impact on a heated aluminum surface
(Universiti Malaysia Perlis (UniMAP), 2016-06)Study of surface roughness during droplet impact on a heated aluminium is to look into the effect of droplet impact on surface roughness after the droplet impinged on the hot surface. The primary problem with this task ... -
Analysis of shrinkage on thick plate part using genetic algorithm
(Universiti Malaysia Perlis (UniMAP), 2016-05)Injection moulding process has been widely used to produce plastic products with various shapes for high productivity and high volume products with low cost. However there are several defect which can influence the quality ... -
Axial and lateral compression behaviour of Flax fibre reinforced epoxy composites with winding at different angle
(Universiti Malaysia Perlis (UniMAP), 2016-06)Nowadays composites made of fibres are used in many types of industries. But there are problem with poor transmission load and low strength of specimen composite tube. This study investigates the effect of filament winding ... -
Product design and development using Design For Assembly (DFA) method: a case study on automated swallow feeding machine
(Universiti Malaysia Perlis (UniMAP), 2016-06)This final year report is focuses on producing design concept of the swallow feeding machine and a case study for easy assembly for automated swallow feeding machine. In order to attract the swallows into the building, ... -
Design and fabrication of portable cleaning machine for raw edible bird’s nest
(Universiti Malaysia Perlis (UniMAP), 2016-06)Edible bird’s nest is one of the demanding food products. Removing the impurities in raw edible bird’s nest is generally known as the most complicated cleaning process especially for Grade C raw edible bird’s nest. ... -
Design and fabricate a mini tensile testing machine
(Universiti Malaysia Perlis (UniMAP), 2016-05)This project is to design and fabricate a small size and portable of tensile test machine that can be used for laboratory teaching purpose. Existing tensile testing machine in laboratory is not enough to accommodate ... -
Design and development of the vibrating sifter system for the existing design of dried chilli seed Separating Machine
(Universiti Malaysia Perlis (UniMAP), 2016-06)Design and development of the vibrating sifter system for the existing design of dried chilli seed separating machine based on the problem existing which to design the adjustable vibrating system of the sifter and the ... -
Preliminary design and development of grain dryer fired by microwave
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project aimed is to determine the potential of obtaining dryer grain in a microwave energy. Grain drying is one of the most energy consuming processes on farms. It has also a lot of potential for energy savings. ... -
Study of surface roughness during droplet impact on a heated stainless steel surface
(Universiti Malaysia Perlis (UniMAP), 2016-06)This is a study of surface roughness during impact of water droplet impinging on a heated stainless steel surface. In this study, the effect of the droplet impingement on the surface were presented. The topic about the ... -
Simulation on usage of water to an explosive compaction
(Universiti Malaysia Perlis (UniMAP), 2016-05)This project is about the simulation on usage of water to an explosive compaction. The explosive compaction is a method to compress the metal powder into desired shape. Emulex is used as an explosive in this project. The ... -
Staggered eye punching process in replacing eye burning process for production of Urethral Foley Catheter
(Universiti Malaysia Perlis (UniMAP), 2016-06)A catheter is a medical device used to drain fluids from the human body. There are variety types of catheter such as cardiovascular, urology, gastrointestinal, neurovascular and ophthalmic catheters. It is commonly made ... -
Study of heat transfer characteristics of Sio2 nanoparticles in heat pipes
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project deal with study of heat transfer characteristics of silicon oxide, SiO2 in heat pipe. To achieve better performance of heat pipe, increasing its efficiency is a challenge nowadays. Effects of implementation ... -
Cycle time variation analysis on shop floor production line – a case study in medical device manufacturing industry
(Universiti Malaysia Perlis (UniMAP), 2016-06)This is a case study of cycle time of machines and production lines of a medical device manufacturing plant. Unstable cycle times leads to unreliable production operation which in turn reduces productivity. More time, ... -
Feasibility study on capturing wind for effective natural ventilation
(Universiti Malaysia Perlis (UniMAP), 2016-06)The main idea of this particular project is to design the effective natural ventilation system. The design should meet the objective of the study which is to study on capturing wind for natural ventilation. In order to ... -
The improvement of the production line of the assembly of audio product
(Universiti Malaysia Perlis (UniMAP), 2016-04)The main reason for low production rate of audio based products were inappropriate handling of assembly process. This study was conducted to reduce the product operating time. By using line-balancing process, this study ... -
Design of a mini fatigue bending test machine
(Universiti Malaysia Perlis (UniMAP), 2016-05)This project focuses on the design and development of science and technology. Mini Bending Fatigue Testing Machine is developed based on the problem of the high cost of providing these machines in large quantities. In ...