School of Manufacturing Engineering (FYP): Recent submissions
Now showing items 321-336 of 336
-
Build mushroom house using a product design phase method that is product generation and evaluation
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)Product Design Phase method that is Product Generation and Evaluation is one of the method to design a Mechanical parts or products. It will consider all the parameter or thing to happen while designing a part or product. ... -
Robust setting of Ti-6Al-4V machining using WEDM (Low Energy with Electrolysis Free Circuit Off )
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)Titanium alloys such as Ti-6Al-4V are increasingly used in aerospace and automotive industries, and also used as medical implant material in wide variety of applications. Wire-electro discharge machining (WEDM) is an ... -
A study on the machining parameters optimization of WEDW machining TI-6AL-4V: effect on surface roughness, MRR and cutting speed
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)The purpose of this project is to optimize the WEDM combination parameters in order to get the highest material removal rate (MRR), fastest cutting speed (CS) and finest surface roughness (SR) on material of titanium alloy ... -
Ergonomics study and analysis of flexible manufacturing system
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-01)Nowadays, the market trend has been demanding increased diversity in product offerings, along with frequent updates to each product. This in turn is influencing manufacturing to invest in more flexible equipment for new ... -
Temperature reduction in mushroom house using the principle of waterfall
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008)The design and concept of mushroom house where can be maintain at 24°c were investigated by using the principle of heat transfer. The water was pumped from the tank to dome roof and flow through the pipe on the both side ... -
Investigate the effect of cutting parameter pn Ti6Al4V surface in EDM wire-cut
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)Titanium aloy is aprovide exellent corrosion resistance, a high strength-to-weight-ratio and good high temperature. It’s also have very high affinity to oxygen. A natural oxide layer is always present on the surface. A ... -
Solar food dryer
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)Solar thermal systems is a practical, economical and the responsible approach environmentally for drying operation, which is applicable to almost all the agricultural product. By means of that, in this project, Solar ... -
Rainwater Catchment System - roofing
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)Rainwater Catchment System is a system that uses rainwater as the water sources for activities such cooking, washing, bathing and others activities that involved water utilization. This system is mostly applied at urban ... -
Design and fabrication of mushroom house to maintain temperature at 26°C
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-01)Concept Generation and Pugh Chart Theories is the method to design the mushroom house. It will consider all the parameter or thing to happen while designing a part or product. It also will guide design process of concept ... -
Stabilization of production rate for plastic products (Single CD) by using injection moulding machine
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)A researched project was designed in order to study the stabilization of production rate for plastic product (single CD) by using injection moulding machine. The study was carried out by identifying the operating parameters ... -
To study a design of two and three-plate mould for injection moulding process
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)The purpose of this project to learn and practice design guideline for plastic injection moulding process in design mould. There include to understand all the factor that will affect the design product example poor design ... -
Design and analysis solar car chassis part
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)A solar car is a lightweight, low power vehicle designed and built with a single purpose in mind – racing. They have limited seating (usually one, sometimes two people), they have very little cargo capacity, and they can ... -
Motorized Wheelbarrow
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)Wheelbarrows have been extensively used for carrying cement, refuse, tools and other materials. It is a simple device that eases the process of transporting materials. However, it requires the user’s strength to push it ... -
Design and fabrication of novel Articulated Robot Arm with mobile movement
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)This project had examined the Design and Fabrication of Novel Articulated Robot Arm with Mobile Movement and Articulated Robot Arm that can perform for Pick and Place function. The project presents the processes undertaken ... -
Design and development of Shredder machine for compost fertilizer production
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)Since years ago till now, the communities especially in Malaysia are not shows their interest in recycling activities and not get attention from them. For example, when we go to the market or any place that sell wet stuffs, ... -
Optimization effect of parameter on surface quality of stainless steel
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)The purpose of this project are to optimize process variables of WEDM to obtain minimum surface roughness and crater size. This research is to get the best cutting parameter for tensile testing where the quality on tensile ...