Browsing Institute of Nano Electronic Engineering (INEE) (Articles) by Author "nazree@unimap.edu.my"

Now showing items 1-12 of 12

    • Characteristic and corrosion studies of rare earth (REE) based anodizing on AZ91D magnesium alloy 

      Khalid Azadi, Mat Akhir; Mohd Zamzuri, Mohammad Zain; Mohd Nazree, Derman, Dr.; Siti Norbahiyah, Mohamad Badari (Trans Tech Publications, 2014-01)
      Oxide coatings on AZ91D magnesium alloy were prepared using anodizing technique with 10mA/cm2 current density for 5 minutes in electrolyte containing Mg (NO₃)₂ with NaVO₃ as an additive. The corrosion behaviors of different ...

    • Comparison study in consolidation of yttria reinforced iron-chromium composites using conventional and microwave sintering technique 

      Marina, Marzuki; Mohd Zamzuri, Mohammad Zain; Mohd Nazree, Derman, Dr.; Mohd Asri, Selamat; Nooraizedfiza, Zainon (Trans Tech Publications, 2014)
      This research is focused on studying the density and mechanical properties of iron-chromium composites consolidated by innovative rapid microwave sintering technology against conventionally sintered counterparts using slow ...

    • Corrosion behavior of Al-Cu-Ni-Y alloys 

      Mohd Nazree, Derman, Dr.; Mohd Jeffry, Radzi; Kumar, R. (Trans Tech Publications, 2013)
      Al based alloy has been widely used in various industries. This research paper aims at the investigation onto the effect of the percentage of Cu and Ni alloying elements in the corrosion behavior of Al-Cu-Ni alloys. The ...

    • The corrosion studies of powder metallurgy Co-Cr-Mo (F-75) alloy 

      Zuraidawani, Che Daud; Shamsul Baharin, Jamaludin, Prof. Dr.; Mohd Nazree, Derman, Dr.; Juyana, A Wahab          (AENSI Publisher All rights reserved, 2013-10)
      Co-Cr-Mo (F-75) alloy was investigated for biomedical application due to its mechanical properties and good corrosion resistance. This study has been focusing on the corrosion behavior of PM Co-Cr-Mo alloy. The Co-Cr-Mo ...

    • Effect of anodizing voltage on the morphology and growth kinetics of porous anodic alumina on Al-0.5 wt% Mn alloys 

      Voon, Chun Hong; Mohd Nazree, Derman, Dr.; Uda, Hashim, Prof. Dr.; Foo, Kai Loong; Tijjani Adam, Shuwa (Trans Tech Publications, 2014)
      In this study, the effect of anodizing voltage on the morphology of porous anodic alumina and growth kinetics of anodizing of aluminium manganese alloy was reported. It was found that the increasing anodizing voltage affect ...

    • Effect of electrolyte concentration on the growth of porous anodic aluminium oxide (AAO) on Al-Mn alloys 

      Voon, Chun Hong; Mohd Nazree, Derman, Dr. (Trans Tech Publications, Switzerland, 2012-12)
      In this study, the effect concentration of electrolyte on pore nucleation process during anodizing was investigated. It was found that the concentration of oxalic acid influenced the morphologies and regularities of porous ...

    • The effect of electrolyte temperature on formation of porous aluminium oxide films in anodising process 

      Juyana, A Wahab         ; Mohd Nazree, Derman, Dr.; Zuraidawani, Che Daud (AENSI Publisher All rights reserved, 2013-10)
      A porous aluminium oxide film formed on aluminium was prepared in a mixed electrolyte of phosphoric acid and acetic acid solution. The morphology, growth and thickness of the film were investigated. The anodising process ...

    • Effect of heat treatment on microstructure and corrosion behavior of Az91d magnesium alloy 

      Chye, Lih T.; Mohd. Zamzuri, Mohammad Zain; Siti Norbahiyah, Mohamad Badari; Khairul Azwan, Ismail, Dr.; Mohd Nazree, Derman, Dr.; Suhaimi, Illias (Trans Tech Publications, 2013)
      An AZ91D ingot in the as-cast condition was homogenized by heat treatment process. Then, the microstructures produced and corrosion behaviour after heat treatment was studied in detail. As-cast AZ91D was recrystallize by ...

    • Effect of manganese content on the fabrication of porous anodic alumina 

      Voon, Chun Hong; Mohd Nazree, Derman, Dr.; Uda, Hashim, Prof. Dr. (Hindawi Publishing Corporation, 2012)
      The influence of manganese content on the formation of well-ordered porous anodic alumina was studied. Porous anodic alumina has been produced on aluminium substrate of different manganese content by single-step anodizing ...

    • Effect of sintering on the physical and mechanical properties of Co-Cr-Mo (F-75)/HAP composites 

      Nur Maizatul Shima, Adzali, Dr.; Shamsul Baharin, Jamaludin, Prof. Dr.; Mohd. Nazree, Derman, Dr. (Universiti Kebangsaan Malaysia, 2013-12)
      This paper reports on the effects of HAP addition and sintering temperature on the microstructure and properties of the F-75/HAP composites fabricated by powder metallurgy. Co-Cr-Mo (F-75) is used in orthopedics because ...

    • Synthesis and characterization of electroless copper coated SiC particles 

      Azmi, Kamardin; Mohd Arif Anuar, Mohd Salleh; Mohd Nazree, Derman, Dr. (Trans Tech Publications, 2013)
      Silicon carbide reinforced copper matrix (Cu-SiCp) composites fabricated via the conventional powder metallurgy methods have inferior thermophysical properties due to the weak bonding between the copper matrix and the SiCp ...

    • The thermal expansion behaviors of Cu-SiCp composites 

      Azmi, Kamardin; Mohd Nazree, Derman, Dr.; Mohd Mustafa Al-Bakri, Abdullah (Trans Tech Publications, 2013)
      The demand for advanced thermal management materials such as silicon carbide reinforced copper matrix (Cu-SiCp) composites is increasing due to their high thermal conductivity and low CTE properties. However, the weak ...