Browsing Researchers by Title
Now showing items 1555-1574 of 3514
-
Height measurement based on fringe projection
(Trans Tech Publications, 2014)A three-dimensional surface measurement using fringe projection technique has received attention among the researches for the last few decades.However choosing the best method is the challenge because one needs to consider ... -
Helical Antenna sensor for Different Liquid Type Identification
(EDP Sciences, 2017)There are variety of lliquid sensor measurement systems that available in the market nowadays. It is used to measure various parameter for wide range application or to address a specific application. However, most of the ... -
Hemodynamic study on upper extremity : simulation on straight reverse Saphenous vein graft
(2012)Artery reconstruction in upper extremities is rare performed compare to the incidence of reconstruction in lower extremities. In many cases, primary vascular repair was performed, whenever, otherwise, the interposition ... -
Hemodynamic study on upper extremity: Simulation on straight reverse saphenous vein graft
(Institute of Electrical and Electronics Engineers (IEEE), 2012-02-27)Artery reconstruction in upper extremities is rare performed compare to the incidence of reconstruction in lower extremities. In many cases, primary vascular repair was performed, whenever, otherwise, the interposition ... -
Heteroepitaxial growth of vacuum-evaporated Si-Ge films on nanostructured silicon substrates
(Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 2015)In this study, a low-cost vacuum-evaporated technique is used in the heteroepitaxial growth of Si-Ge films. Three different surface variations are employed: i.e. polished Si, Si micropyramids and Si nanopillars profiles. ... -
Hexagon platinum Schottky contact with ZnO thin film for hydrogen sensing
(Penerbit UTM Press, 2013)This paper reports on the study of the effect on adding total peripheries and sharp edges to the Schottky contact as a hydrogen sensor. Schottky contact was successfully designed and fabricated as hexagon-shape. The contact ... -
High deadline meeting rate of non-preemptive dynamic soft real time scheduling algorithm
(Institute of Electrical and Electronics Engineers (IEEE), 2012-11)Hard real time systems were often implemented with preemptive scheduling, which gives priority to the highest priority task. In this paper we present a new non-preemptive scheduling of jobs meant for soft real time ... -
High degree of testability using full scan chain and ATPG-An industrial perspective
(Asian Network for Scientific Information, 2009)This study describes an efficient design methodology from an industrial perspective on utilizing Register Transfer Level (RTL) coding style, full scan chain implementation and Automatic Test Pattern Generation (ATPG) to ... -
High Gain and High Directive of Antenna Arrays Utilizing Dielectric Layer on Bismuth Titanate Ceramics
(Hindawi Publishing Corporation, 2012-06-25)A high gain and high directive microstrip patch array antenna formed from dielectric layer stacked on bismuth titanate (BiT) ceramics have been investigated, fabricated, and measured. The antennas are designed and constructed ... -
High gain and high directive of antenna arrays utilizing dielectric layer on Bismuth Titanate ceramics
(Hindawi Limited, 2012)A high gain and high directive microstrip patch array antenna formed from dielectric layer stacked on bismuth titanate (BiT) ceramics have been investigated, fabricated, and measured. The antennas are designed and constructed ... -
High linearity on-chip mixer for 46 LTE wireless communication
(Universiti Malaysia Perlis (UniMAP)School of Microelectronic Engineering, 2014-05)The growth of 4G wireless communication system, a high performances, simple circuitry and low cost wireless transmitters are required. One of the main radio frequency (RF) circuits in the wireless communication transmitter ... -
High performance systolic array core architecture design for DNA sequencer
(EDP Sciences, 2018)This paper presents a high performance systolic array (SA) core architecture design for Deoxyribonucleic Acid (DNA) sequencer. The core implements the affine gap penalty score Smith-Waterman (SW) algorithm. This time-consuming ... -
High power LED heat dissipation analysis via copper diamond slug
(AENSI Publisher All rights reserved, 2013-10)The emergence of high power light emitting diode as a novel electronic based light source is due to its vast advantage in terms of optical efficacy, low power consumption and enhanced life time. However, the performances ... -
High side MOSFET driver design using discrete components for low voltage applications
(Universiti Malaysia Perlis (UniMAP)Centre for Graduate Studies, 2010-10-16)This paper presents the design of a high-side N-channel MOSFET driver using discrete components for low voltage applications, ranging from 3V up to 24Vdc operation. Special level shifting technique is used to increase the ... -
High speed and low power devices : bulk silicon versus SOI
(Kolej Universiti Kejuruteraan Utara Malaysia, 2005-04) -
High Strength K-Brick: Rapid Set Brick
(School of Materials Engineering, 2008-01-09) -
High temperature corrosion behaviour of steel with a Carbonate deposit at 1123K
(School of Materials Engineering, 2007)The high temperature corrosion behavior of A1S1 304 austenitic stainless steel and S45C carbon steel were studied in presence with CaCO3 salt at 1123K for 24,48,72, 96 and 120 hour. The studies were carried out to determine ... -
High temperature creep and hydrogen embrittlement failure of a steam trap bypass tube
(Trans Tech Publications, 2013)A coal fired power plant with its normal operation temperature of 540°C in which its steam trap bypass tube in that power plant was totally fractured. The aim of this study is to explore the evidence related to the steam ... -
High-end technology for effective glass manufacturing industry: Innovative operating environment.
(LAMBERT Academic Publishing, 2013)The book is discussed on the design, analysis and fabrication of Articulated Robotic Arm for handling glass product. The project is to differentiate glass and other objects based on reflective theory. The discussion shows ... -
High-end technology for effective operating environment in a glass manufacturing industry
(Universiti Malaysia PerlisPusat Pengajian Kejuruteraan Mekatronik, 2012-02-27)Currently glass production industry is growing at a very fast rate and its need high technology procedure to support its manufacturing process. To provide an efficient manufacturing environment such as producing, ...