Browsing School of Manufacturing Engineering (FYP) by Issue Date
Now showing items 21-40 of 336
-
Design of a chicken roaster grilling machine
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)It is known that, common chicken roaster grilling machine is associated with uncomfortable working environment where the worker is exposed to heat and excessive smoke. The quality and consistency of the finish products ... -
Investigation new sensing SnTiO3 as thin film light sensor
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)In this project, some research has been done on Tin dioxide (SnO2) and stannium titanate perovskite (SnTiO3) thin films. It has been known that tin dioxide has various applications, especially for gas sensor, light sensor, ... -
Motorized Wheelbarrow
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)Wheelbarrows have been extensively used for carrying cement, refuse, tools and other materials. It is a simple device that eases the process of transporting materials. However, it requires the user’s strength to push it ... -
Robust setting of Ti-6Al-4V machining using WEDM (High energy with EF Circuit Off)
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)In this project, some research had been done on optimization of wire electrical discharge machining (WEDM) parameters. It has been known that WEDM is a specialized thermal machining process which accurately machines parts ... -
The effect of pollution production in gas burner combustion system using Curve Vane Radial Air Swirler
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)Swirling flow is a main flow produced by air swirled in gas turbine engine. Such flow is the combination of swirling and vortex breakdown. Swirling flow is widely used to stabilize the flame in combustion chamber. Its ... -
The effect of pollution production in gas burner system using Flat Vane Axial Air Swirler
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)A liquid fuel burner system with Flat Vane axial air swirler with vane angle of 20° and 60° has been investigated using combustor. Flange plates with 40mm (4cm) were inserted at the back plate of swirler outlet. All tests ... -
Designing a pressure gauge / indicator for kitchen gas stove
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)A kitchen stove, cooker or cook stove is a kitchen appliance designed for the purpose of cooking food. Kitchen stoves rely on the application of direct heat for the cooking process and may also contain an oven, used for ... -
Rainwater Catchment system – storage tank
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)Rainwater Catchment System is a system that collects rainfall from the catchment area and will be store in the water storage tank. This rainfall collection will be used as the water sources for activities such cooking, ... -
Design and fabrication of novel Articulated Robot Arm with mobile movement
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)This project had examined the Design and Fabrication of Novel Articulated Robot Arm with Mobile Movement and Articulated Robot Arm that can perform for Pick and Place function. The project presents the processes undertaken ... -
Design and development of Shredder machine for compost fertilizer production
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)Since years ago till now, the communities especially in Malaysia are not shows their interest in recycling activities and not get attention from them. For example, when we go to the market or any place that sell wet stuffs, ... -
Design and analysis solar car chassis part
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)A solar car is a lightweight, low power vehicle designed and built with a single purpose in mind – racing. They have limited seating (usually one, sometimes two people), they have very little cargo capacity, and they can ... -
Reusability of plastics
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)It is a challenge to reduce the ever-increasing flow of plastics waste. This study was undertaken to investigate the viability of recycling plastics products and their capabilities in substituting virgin plastics in the ... -
Investigate the effect of cutting parameter pn Ti6Al4V surface in EDM wire-cut
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)Titanium aloy is aprovide exellent corrosion resistance, a high strength-to-weight-ratio and good high temperature. It’s also have very high affinity to oxygen. A natural oxide layer is always present on the surface. A ... -
Experiment studies using waterfall stones and Labu Sayung to reduce the temperature of water based on concept of heat transfer
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)This experiment was held to determine whether the usage of natural resources such as stone from waterfall and “labu sayong” that made from clay will reduce the temperature of water contained in it naturally. When we go to ... -
Design and fabrication of novel Articulated Robot Arm with mobile movement
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)This project had examined the Design and Fabrication of Novel Articulated Robot Arm with Mobile Movement and Articulated Robot Arm that can perform for Pick and Place function. The project presents the processes undertaken ... -
Experimental design of Crystallization processes using classical method
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)Crystallization has become one of the most important unit operations in the sugar cane processing. The need to reduce the time from product discovery to market introduction is an inherent concern. In order to achieve the ... -
Design and development Centrifugal Atomization machine for metal powder production – part 1
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)Atomization is one of the processes for making the powder metal for powder metallurgy process. Atomization actually is the process where the molten metal was disintegrated into small droplets and rapidly solidified before ... -
Optimization of 950K PMMA resists for Nano-application using Statistical Design Expert
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)This paper discusses the application of a design of experiments (DOE) experimental method for analyzing the influence of four parameters (coating time, spinning speed, and softbake time and softbake temperature).involved ... -
A study on the use of high pressure application for destruction of microorganism in soymilk
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)The current method of soymilk processing proved to be degrading to the quality of milk and its product. Due to this, this project was carried out for the purpose of investigating the application of ultrasonic wave as an ... -
Design and development of low cost vertical farming
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-05)Modernize agricultural activity is a one method that can increase productivity agricultural production. Fertigation method is a good alternative method and has the ability for progressive. Fertigation combines the two main ...