School of Electrical Systems Engineering (FYP): Recent submissions
Now showing items 101-120 of 218
-
Mini underwater hydro energy model using flipwing turbine
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)The main objective of this project is to study about the renewable energy. Renewable energy is energy which comes from natural resources such as sunlight, wind, water and geothermal heat which are renewable (naturally ... -
LED lamp driver using Cuk converter
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)Recently, Light Emitting Diodes (LEDs) replacement lamps become a viable alternative for incandescent lamp due to the quality of light, lamp life and environmental cost of ownership. One of the critical elements in LEDs ... -
Effect of symmetrical voltage sags on induction motor and comparison solutions
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)This final year project will analyze the symmetrical voltage sags and short interruption on the induction machines behavior: current, voltage torque and speed loss. These effects depend on several variables like sag magnitude ... -
Control unit of wind turbine for 12 V battery charger
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)Energy produced by wind turbines does not produce pollutants like other sources of energy (i.e. coal, gas, and petroleum based fuel). Wind energy may help to reduce the air pollutions by replacing the current sources of ... -
Case study of a linear generator as wave energy converter
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)This project focused on case study of a linear generator as wave energy converter. The types of linear generator focus in this study which is suitable on wave which is turbular permanent magnet. There are various models ... -
Modeling and control of a DC-DC converter
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)This project presents the modeling and control of a DC-DC converter. The project aims is to develop a buck converter with the capacitor voltage and inductor current as the outputs and be able to monitor the output voltage ... -
Study of effectiveness PID controller for the selected case studies
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)PID (Proportional – Integral – Derivative) provides an efficient solution in many real-world control system problems. The main purpose of this final year project is to provide a general overview of the PID controller. This ... -
Serial stepper motor controller
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-06)The theory of stepper motor control has evolved since the late 18th century. Simply, Stepper motor control is defined as accurately controlling the movement of an object based on speed, distance, load, inertia or a ... -
Boost converter latch up
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-06)This report presents the design and analysis of a Boost Converter that will demonstrate latch up with following specification: Vin=12V, Vout=24V, Pout=60W and peak to peak output voltage ripple is 3%. PSIM software is ... -
Embedded Generation (EG) allocation using Artificial Bee Colony (ABC) algorithm
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)This Final Year Project is proposed to study the Artificial Bee Colony (ABC) algorithm in determining the location and sizing of Embedded Generation (EG) in distribution network. The purpose is to minimize total system ... -
Design and construct a three phase 5kVA, 1/0.415kV power transformer
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-04)The purpose of this Final Year Project is to understanding the knowledge and theoretical of three phase transformer. The three phase transformer which is step-up from 415V to 1000V with a capacity 5kVA has been designed. ... -
Charge measurement system
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)This project discusses the design of charge measurement meter. This instrument was used to measure the rate of charges for different surroundings. Construct a capacitor plate to capture the charge, connect the capacitor ... -
Design and construct of 1.5kVA auto transformer
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-04)This project presents the design, analysis, and development of an autotransformer to producing the output voltage range in 6V, 12V, 24V, 50V, 100V, 125V, 150V and 200V with the rated power of 1.5kVA. The design should ... -
Study effect of climate factor on grounding resistivity around UniMAP campus
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-04)Soil resistivity data is the key factor in designing a grounding system for a specific performance objective like a climate factor. All soil conducts electrical current, with some soil having good electrical conductivity ... -
Design of inverter for high current load application
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)The purpose of this project is to research and design a Direct Current (DC) to Alternating Current (AC) inverter. This inverter is design to create 240 Volt (V) AC with 1000 Watt maximum output. The output of this inverter ... -
A portable joystick controller for DC motors
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)This project is to design a portable joystick that can control two units of motors at the same time. Joystick is more flexible to handle compared with pushed button. In this project, four units of relays are used in the ... -
Design single phase transformer
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-04)This project has presented the design of 1 kVA rated power, 200/100 V and cable of 1.5 cross sectional area. The design of transformer coil starts with the selection of number of turns of coil and selection of cable ... -
A gadget for blind people to use in daily activities
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)This project discusses the design of an Ultrasonic Blind Stick that creating to help blind people to walk and do their activities easier. This stick use battery 9V as voltage supply and ultrasonic sensor to detect things ... -
Effect of Voltage Sag and Mitigation on induction motor behavior
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)For some decades, power quality did not cause any problem, because it had no effect on most of the loads connected to the electric distribution system. When an induction motor is subjected to voltage sag, the motor still ... -
Development of New Copper Rotor for AC Induction Motor
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)This final year project is based on the demonstrated design methods with manufacturing process parameters that have enabled economical production of development of new copper rotors. This is require the experimental work ...