Now showing items 1-20 of 42

    • 3D finite element stress analysis of butt adhesively bonded dissimilar joint: effect of bond thickness on strength 

      Izzawati, Basirom; Mohd Afendi, Rojan, Dr.; M. Afif; Siti Nurhashima; Ruslizam, Daud, Dr.; Nasrul Amri, Mohd Amin, Dr.; Mohd Shukry, Abdul Majid, Dr. (Trans Tech Publications, 2014-06)
      The butt joint is the most studied type of adhesive joints in the literature. However, the joint strength prediction of joints is still a controversial issue as it involves a lot of factors that are difficult to quantify ...
    • Acoustic emission monitoring of multiaxial ultimate elastic wall stress tests of glass fibre-reinforced epoxy composite pipes 

      Mohd Shukry, Abdul Majid; Mohd Afendi, Rojan, Dr.; Ruslizam, Daud, Dr.; Gibson, A.G.; T.A., Assaleh; Hale, J.M.; Hekman, M. (Taylor & Francis, 2014-01)
      This paper describes the acoustic emission (AE) monitoring of multiaxial ultimate elastic wall stress (UEWS) tests of filament wound glass fibre-reinforced epoxy composite pipes under hydrostatic, pure axial and pure hoop ...
    • Application of frame energy based DCT moments for the damage diagnosis in steel plates using FLNN 

      Paulraj, Murugesa Pandiyan, Prof. Dr.; Sazali, Yaacob, Prof. Dr.; Mohd Shukry, Abdul Majid, Dr.; Krishnan, Pranesh (IEEE Conference Publications, 2012-12)
      This paper discusses the application of frame energy based Discrete Cosine Transformation (DCT) moment features for the detection of damages in steel plates. A simple experimental model is devised to suspend the steel ...
    • The behavior of Projectile Ricochet off various wooden targets 

      Mohd Shukry, Abdul Majid; Birch, Robert S.; M.I. Jais; Mohd Noor Arib, Md Rejab; Hafizawati, Zakaria (Kolej Universiti Kejuruteraan Utara Malaysia, 2006)
      This paper details the assessment of bullet ricochet as a function of incident angle and the impact plate material. A series of experimental testing have been carried out on three different woods chosen to give range of ...
    • Damage detection in steel plates using artificial neural networks 

      Paulraj, Murugesa Pandiyan, Prof. Madya; Mohd Shukri, Abdul Majid; Sazali, Yaacob, Prof. Dr.; Mohd Hafiz, Fazalul Rahiman; Krishnan, R. P. (Institute of Electrical and Electronics Engineering (IEEE), 2009-06-04)
      In this paper, a simple method for crack identification in steel plates based on frame energy based Discrete Cosine Transformation (DCT) is presented. A simple experimental procedure is also proposed to measure the vibration ...
    • Damage detection in steel plates using discrete cosine transformation techniques and artificial neural network 

      Paulraj, M.P.; Mohd Shukry, Abdul Majid; Sazali, Yaacob; Mohd Hafiz, Fazalul Rahiman; R Pranesh, Krishnan (Universiti Malaysia Perlis, 2009-10-11)
      In this paper, a simple method for crack identification in steel plates based on the Frame Energy based Discrete Cosine Transformation [DCT] moments is presented. A simple experimental procedure is also proposed to measure ...
    • Dielectric spectroscopy of pharmaceutical drug (Paracetamol) dosage in water 

      Cheng, Ee Meng, Dr.; Mohd Fareq, Abd. Malek, Dr.; Farrah Salwani, Abdullah; Wee, Fwen Hoon; Khor, Shing Fan; Lee, Yeng Seng; Mohd Afendi, Rojan, Dr.; Mohd Shukry, Abdul Majid, Dr.; Shahriman, Abu Bakar, Dr.; Wan Khairunizam, Wan Ahmad, Dr.; Liyana, Z. Y. (IEEE Conference Publications, 2013-12)
      This paper discuss about the dielectric measurement on different concentration of pharmaceutical drug using Agilent 85070E High-Temperature and Slim form probe. A microwave dielectric measurement is set up to measure dosage ...
    • Effect of adhesive thickness on adhesively bonded T-joint 

      A. R., Abdullah; Mohd Afendi, Rojan, Dr.; Mohd Shukry, Abdul Majid, Dr. (IOP Publishing Ltd, 2013)
      The aim of this work is to analyze the effect of adhesive thickness on tensile strength of adhesively bonded stainless steel T-joint. Specimens were made from SUS 304 Stainless Steel plate and SUS 304 Stainless Steel ...
    • Effect of nano-clay and their dispersion techniques on compressive properties of unsaturated polyester resin 

      Fartini, Mohd Suhut; Mohd Shukry, Abdul Majid, Dr.; Mohd Afendi, Rojan, Dr.; Ruslizam, Daud, Dr.; Azizul, Mohamad (Trans Tech Publications, 2014-06)
      This paper aims to understand the relationship between processing parameters and compressive properties of nanoclay filled polyester resin (dispersion method and wt% of nanoclay particles). Unsaturated polyester resin with ...
    • Effects of elevated temperatures on the compression strength of nanoclay filled unsaturated polyester resin 

      Fartini, Mohd Suhut; Mohd Shukry, Abdul Majid, Dr.; Mohd Afendi, Rojan, Dr.; Nasrul Amri, Mohd Amin, Dr.; Azizul, Mohamad (Trans Tech Publications, 2014-06)
      The paper describes the effects of the montmorillonite (MMT) fillers commonly known as nanoclay, on the compression properties of unsaturated polyester resins at different weight percentage of nanoclay. Modified resin ...
    • The effects of varying target hardness on ricochet angle 

      Mohd Shukry, Abdul Majid; Birch, Robert S.; Jais, M. I. (American Institute of Physics, 2007-05-09)
      This project is a study on ricochet characteristics off wooden targets when fired upon by 22 calibre bolt action rifle. A series of experimental testing has been carried out on three different woods chosen to give range ...
    • Effects of winding angles in biaxial ultimate elastic wall stress (UEWS) tests of glass fibre reinforced epoxy (GRE) composite pipes 

      Mohd Shukry, Abdul Majid; Mohd Afendi, Rojan, Dr.; Ruslizam, Daud; Gibson, A. G.; M., Hekman (Universiti Malaysia Perlis (UniMAP), 2013-03-26)
      This paper presents an experimental investigation into the influence of winding angles in multiaxial ultimate elastic wall stress (UEWS) tests of glass-fibre reinforced epoxy (GRE) composite pipes. Currently, UEWS test is ...
    • Effects of winding angles in biaxial ultimate elastic wall stress (UEWS) tests of glass gibre reinforced epoxy (GRE) composite pipes 

      Mohd Shukry, Abdul Majid, Dr.; Mohd Afendi, Rojan, Dr.; Ruslizam, Daud, Dr.; Gibson, A. G.; M., Hekman (Trans Tech Publications, 2013)
      This paper presents an experimental investigation into the influence of winding angles in multiaxial ultimate elastic wall stress (UEWS) tests of glass-fibre reinforced epoxy (GRE) composite pipes. Currently, UEWS test is ...
    • Electrical properties investigation of unsaturated polyester resin with carbon black as fillers 

      R., Revati; Shuhaida, Yahud, Dr.; Mohd Shukry, Abdul Majid, Dr. (Trans Tech Publications, 2014-06)
      In this paper, conducting polymer composites were prepared by adding different percentage of carbon black (2, 4, 6 and 8)% to unsaturated polyester resin. Hence, this project focuses on two types of carbon black which is ...
    • Experimental investigation of PCM spheres in thermal energy storage system 

      Nasrul Amri, Mohd Amin, Dr.; Azizul, Mohamad; Mohd Shukry, Abdul Majid, Dr.; Mohd Afendi, Rojan, Dr.; Bruno, Frank, Dr.; Belusko, Martin (Trans Tech Publications, 2013)
      This paper presents the experimental result of a small scale packed bed of random spheres with encapsulated PCM being charged and discharged. A vapor compression refrigerator and heated room with fan heater were used to ...
    • Experimental studies of a Ranque-Hilsch vortex tube 

      Azizul, Mohamad; Nasrul Amri, Mohd Amin; Zuradzman, Mohamad Razlan; Mohd Shukry, Abdul Majid (Trans Tech Publications, 2013)
      Vortex tube is a device that separates a compressed flow of gas into two streams simultaneously, one giving kinetic energy to the other, resulting one hotter than the inlet temperature and one lower, without having any ...
    • General lifetime damage model for glass fibre reinforced epoxy (GRE) composite pipes under multiaxial loading 

      Azizul, Mohamad; Mohd Afendi, Rojan, Dr.; M, Hekman; Gibson, A.G; Mohd Shukry, Abdul Majid, Dr.; Nasrul Amri, Mohd Amin, Dr.; Ruslizam, Daud, Dr.; Meng, Cheng Ee, Dr. (Trans Tech Publications, 2014)
      This paper presents the modelling of a general lifetime performance for glass fibre reinforced epoxy (GRE) composite pipes similar to the well-known Tsai-Hill interactive failure criterion. Tsai Hill criterion is based ...
    • General lifetime damage model for glass fibre reinforced epoxy (GRE) composite pipes under multiaxial loading 

      Mohd Shukry, Abdul Majid, Dr.; Mohd Afendi, Rojan, Dr.; Nasrul Amri, Mohd Amin; Ruslizam, Daud, Dr.; Azizul, Mohamad; Cheng, E.M.; Gibson, A.G.; M. Hekman (Trans Tech Publications, 2014)
      This paper presents the modelling of a general lifetime performance for glass fibre reinforced epoxy (GRE) composite pipes similar to the well-known Tsai-Hill interactive failure criterion. Tsai Hill criterion is based on ...
    • The interlaminar shear strength test of helical wound glass fibre reinforced epoxy laminates subjected to hydrothermal ageing 

      Mohd Shukry, Abdul Majid, Dr.; Mohd Afendi, Rojan, Dr.; Ruslizam, Daud, Dr.; Nasrul Amri, Mohd Amin, Dr.; Azizul, Mohamad; M. Hekman (Trans Tech Publications, 2014-06)
      This paper presents the experimental investigation of interlaminar shear strength (ILSS) tests of helical wound glass fibre reinforced epoxy (GRE) pipes subjected to hydrothermal ageing. Currently, the test is being used ...
    • Kuin not facing problems, says Azizan 

      Embun, Majid (The Star, 2012-09-27)