Browsing Journal Articles by Title
Now showing items 1368-1387 of 2800
-
The influence of CB, silica and CaCO₃ on tensile and morphological properties of vPE/rPE/EPDM blends
(Trans Tech Publications, 2014)The virgin polyethylene (vPE) and recycled polyethylene (rPE) was melt blended with ethylene propylene diene terpolymer (EPDM) in different ratio by using a Haake Rheomix at 180°C and 50 rpm were prepared. The characterization ... -
Influence of Coaches Behaviour On Elite Volleyball Players’ Motivational Climate and Performance Satisfaction
(Kementerian Pendidikan Tinggi (KPT), Malaysia, 2018)Introduction. Coaching behaviour, motivational climate and its influence towards performance satisfaction are important in understanding the development and growth of athletes. In general, positive coaching behaviours could ... -
Influence of Code Size Variation on the Performance of 2D Hybrid ZCC/MD in OCDMA System
(EDP Sciences, 2018)Several two dimensional OCDMA have been developed in order to overcome many problems in optical network, enhancing cardinality, suppress Multiple Access Interference (MAI) and mitigate Phase Induced Intensity Noise (PIIN). ... -
The influence of cure characteristics and crosslink density of virgin acrylonitrile butadiene rubber/recycled acrylonitrile butadiene rubber (vNBR/rNBR) blends
(Trans Tech Publications, 2014)Cure characteristics and crosslink density of virgin acrylonitrile butadiene rubber/recycled acrylonitrile butadiene rubber (vNBR/rNBR) blends were studied. Three different size ranges of rNBR particles, i.e., 150 - 350 ... -
The influence of curing periods on the compressive strength of fly ash-based geopolymer at different aging times
(Trans Tech Publications, 2012)The results of the current experimental investigation indicate the significant effect of the heating periods on the compressive strength of fly ash-based geopolymers prepared at different alkaline liquid content at both ... -
Influence of current density on porous silicon characteristics
(Trans Tech Publications, 2013)Porous silicon structures have been fabricated by electrochemical etching using different current density. From field emission scanning electron microscope images (FE-SEM) it was observed that more uniform distribution of ... -
The influence of deposition temperature on the morphology and corrosion resistance of zinc phosphate coating on mild steel
(Trans Tech Publications, 2013)The influence of phosphating temperature on the surface morphology and corrosion resistance of zinc phosphate coatings on mild steel was investigated. The phosphate layers were deposited on steel from phosphating bath at ... -
The influence of different core arrangements on magnetic properties of electrical sheets under one-dimensional magnetizing system
(Institute of Electrical and Electronics Engineering (IEEE), 2007-12-06)This paper is concerned with the measurement on the magnetic properties of electrical steels under one-dimensional magnetizing system at the frequency of 50 Hz. The magnetic properties were principally investigated by ... -
Influence of different exchange correlation potentials on band structure and optical constant calculations of ZrGa2 and ZrGe2 single crystals
(Elsevier B.V., 2013-10)The all-electron full potential linearized augmented plane wave method was used to solve the Kohn Sham DFT equations. We have employed different approximations for the exchange correlation potentials, namely: LDA, GGA and ... -
The influence of different mold temperature on warpage in a thin shallow injection molding process
(Praise Worthy Prize S.r.l., 2012)Every injection molding parameter have its own influence towards the quality of an injection-molded part. Temperature, pressure and time are main parameters that typically highlighted in controlling the warpage defect of ... -
Influence of different synthesis approach on doping behavior of silver nanoparticles onto the iron oxide-silica coreshell surfaces
(Springer Science+Business Media B.V., 2012-07)Silver (Ag) nanoparticles with the crystallite size ranging from 13-24 nm were successfully doped onto the surface of iron oxide-silica coreshell particles. In the process, iron oxide particles having a size distribution ... -
Influence of dissipation power in copper sputtering plasma measured by optical emission spectroscopy
(Trans Tech Publications, 2014)Copper oxide is a low cost material, easy process fabrication and sensitivity to ambient conditions. Therefore, it is a suitable p-type semiconductor oxides material to be used as a gas sensing material. In order to raise ... -
Influence of dolomite on the mechanical properties of boiler ash geopolymer paste
(Trans Tech Publications, 2014)The waste material from palm oil industry has been increasing since Malaysia was the world largest exported of palm oil mill. The waste such as palm fibers, nut shells, palm kernel and empty fruit bunches are the solid ... -
The Influence of Forensic Accounting Competence and Independent Audit Committee on Anti-Fraud in Firm Performance
(School of Business Innovation and Technopreneurship, Universiti Malaysia Perlis (UniMAP), 2022-06)Anti-fraud is a special field in identifying, diagnosing and treating fraud, and entails the gathering, management, investigation, and utilisation of business data. This research investigated the effect of both the forensic ... -
Influence of gamma irradiation on the electrical conductivity and dielectric properties of polypyrrole conducting polymer composite films
(Universiti Malaysia Perlis (UniMAP), 2019-10)Electrical conductivity and dielectric properties of polypyrrole conducting polymer composite films were investigated using gamma irradiation from 0 kGy up to 25 kGy. The AC conductivity is directly proportional to the ... -
Influence of Heavy Metal on activated Sludge activity: DO and SOUR monitoring
(Universiti Malaysia Perils, 2007)The objective of this study is to evaluate the inhibitory effect of heavy metals on activity of activated sludge microbes, under sequencing batch reactor (SBR) operation, based on dissolved oxygen (DO) and specific oxygen ... -
The influence of human head model wearing metal-frame spectacles to the changes of SAR and antenna gain: Simulation of frontal face exposure
(EMW Publishing, 2013)The relationship between specific absorption rate (SAR) and antenna gain inside the head due to the metal-frame spectacles was investigated. The radio frequency (RF) energy source considered is the smartphone used in the ... -
The influence of human head model wearing metal-frame spectacles to the changes of SAR and antenna gain: Simulation of frontal face exposure
(EMW Publishing, 2013)The relationship between specific absorption rate (SAR) and antenna gain inside the head due to the metal-frame spectacles was investigated. The radio frequency (RF) energy source considered is the smartphone used in the ... -
The influence of job stress towards turnover intention among generation Y employees in Perak Information Technology (IT) industry
(School of Business Innovation and Technopreneurship, Universiti Malaysia Perlis (UniMAP), 2023-06)Researchers have been studying turnover intention for nearly a century. Recently, most generation Y workforce in Malaysia's Information Technology (IT) industry reportedly developed a norm of switching jobs constantly ... -
Influence of Material Properties on the Fluid-Structure Interaction aspects during Molded Underfill Process
(EDP Sciences, 2017-02)This paper presents the investigation of the effects of epoxy moulding compound’ (EMC) viscosity on the FSI aspects during moulded underfill process (MUF). Finite volume (FV) code and finite element (FE) code were connected ...