Browsing by Title
Now showing items 21430-21449 of 78729
-
Fabrication and investigation of copper rotor bar on 0.5HP induction Motor-A performance and economical study
(Australian Journal of Basic and Applied Sciences, 2011-05)The paper deals with the fabrication of copper rotor bars for 0.5HP induction motor and then comparing it with the existing aluminium rotor bars. From this experiment the rotors are compared in terms of efficiency increment ... -
Fabrication and mechanical properties of composite palm ash mixed with phenolic resins
(International Network for Scientific Information Publication (INSI), 2011-11)Brake pad is one of the important engineering components in automobile and it is fabricated by combination of various materials. Asbestos is one of the components in brake pad that is harmful to the human. In this ... -
Fabrication and properties of Aluminium reinforced calcined dolomite and ferrosilicon by powder metallurgy route
(Universiti Malaysia PerlisSchool of Materials Engineering, 2007) -
Fabrication and properties of magnesium-calcium alloy via powder metallurgy technique
Composition of Mg-Ca alloys were prepared by powder metallurgy (PM) method with addition of different calcium content and sintering temperature. This is to evaluate the effect caused by the amount of calcium content and ... -
Fabrication and properties of ternary Al-Mg-Zn alloy filled with polypropylene: Progress report
(Universiti Malaysia Perlis (UniMAP)Centre for Graduate Studies, 2010-10-16)Alloy is produced to enhance the properties of a metal itself and it contributes to the human and society in different applications. In this research, a ternary alloy filled with the polypropylene will be fabricated ... -
Fabrication and simulation of PNP Bipolar transistor based on Spin On Dopant technique and Electrical characterization
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)In this project, the fabrication and simulation of pnp transistor was performed. From fabrication process, the electrical characteristic and sheet resistance of the device was observed by 4 point probe measurement. The ... -
The fabrication methods of Metal-molecule-metal junction electrode current state-of-art
(Universiti Malaysia Perlis (UniMAP), 2012-06-18)Fabrication techniques for Metal-molecule-metal junction electrode suitable to study electron tunneling through metal junctions are reviewed. The applications of current strategies such as mechanical breakjunction, ... -
Fabrication of 2D membrane castellated and straight electrode for dielectrophoresis
(Universiti Malaysia Perlis (UniMAP), 2020-12)This paper is presenting two fabrication process of electrodes for the used in artificial kidney. The electrodes were made to compare which will represent the best results. Both electrodes undergoes same fabrications process ... -
Fabrication of 3C-silicon carbide membranes: Towards development of novel microdevices for biomedical applications
(Institute of Electrical and Electronics Engineers (IEEE), 2012-02-27)3C-SiC is currently under intense study as a potential material for implantable low power blood pressure sensing due to its biocompatibility. In this work, we present and discuss the fabrication processes for n-type 3C-SiC ... -
Fabrication Of 50 µm transistor and AlNiAu interconnection process
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2007-03)Generally process fabrication transistor will starts by cleaning the wafer, formation region drain, D and source, S, get oxide and deposited aluminum as contact with the source, drain and gate. Mask is very important thing ... -
Fabrication of a cost-effective MEMS-based piezoresistive cantilever sensor for gait movement analysis
(Kementerian Pendidikan Tinggi (KPT), Malaysia, 2016)Gait analysis measurement is a method used to access and identify gait events and the measurements of motion parameters involving the lower part of the body. This significant method is widely used in rehabilitation, sports, ... -
Fabrication of a Hand-held Electronic Nose
(Universiti Malaysia Perlis, 2007)An electronic nose is a device that performs the electronic olfactory to substitute human experts. The development of these devices is growing faster due to higher demand. However, current electronic noses usually are very ... -
Fabrication of a novel dye sensitized solar cell by using organic bye from dragon fruit and spinach chlorophyll extract
(Macao Innnovation & Invention Association, 2013-06-28)Conventional energy sources based on oil, coal and natural gas have proven to be highly effective drivers of economic progress, but at the same time damaging to the environment and to human health. Development of clean ... -
Fabrication of Al-based metallic glasses by mechanical alloying and hot consolidation
(Universiti Malaysia Perlis (UniMAP), 2017-04)This project is related to fabrication of aluminium based amorphous metallic glasses. Elemental powder of aluminium, copper and nickel were used for the purposed mentioned. The element powders with nominal composition ... -
Fabrication of Amorphous silicon Microgap Structure for Energy Saving Devices
(Universiti Kebangsaan Malaysia, 2011-11-18)We report here the fabrication of microgaps electrodes on amorphous silicon using low cost techniques such as vacuum deposition and conventional lithography. Amorphous silicon is a low cost material and has desirable ... -
Fabrication of amorphous silicon microgap structure for energy saving devices
(Sains Malaysiana., 2012-06)We report here the fabrication of microgaps electrodes on amorphous silicon using low cost techniques such as vacuum deposition and conventional lithography. Amorphous silicon is a low cost material and has desirable ... -
The fabrication of artificial marble from dolomite (Batu Reput)
(The Mineral, Metals & Materials Society (TMS), 2006-01)Perlis is one of the major producers of "Batu Reput" in Malaysia and majority of the deposits contain of high-purity calcium and magnesium carbonate. The composition of Batu Reput is similar with the ordinary dolomite. ... -
Fabrication of BaTiO3 thin films through ink-jet printing of TiO2 sol and soluble Ba salts
(Elsevier Ltd., 2007)BaTiO3 thin films were prepared by ink-jet printing aqueous solutions of TiO2 sol and soluble Ba salts. Higher pH values (pH > 13) as well as higher than stoichiometric Ba (Ba:Ti = 1.1:1) salt additions were required to ... -
Fabrication of calcium phosphate coating on pure magnesium substrate via simple chemical conversion coating: surface properties and corrosion performance evaluations
(Elsevier, 2018)The main objective of the current work was to fabricate calcium phosphate (CaP) coating on 99.9% purity magnesium, Mg substrate through simple chemical conversion method and evaluated the surface properties and corrosion ... -
Fabrication of carbon nanotube field-effect transistor using shadow mask technique
(Universiti Malaysia Perlis (UniMAP), 2022-07)In this work, a new approach based on shadow mask has been reported for fabricating low-cost carbon nanotube field-effect transistor (CNFET) with interdigitated source and drain electrodes. The drop cast method is used for ...