Mohd Ridzuan Mohd Jamir

 

This page provides access to research works by Mohd Ridzuan Mohd Jamir, currently a Lecturer of School of Mechatronic Engineering, Universiti Malaysia Perlis (UniMAP).

News

Skills and Expertise:Material Characterization,Materials,Mechanical Properties Mechanical Behavior of Materials,Microstructure,Materials Processing,Mechanical Testing Robotics,Materials Testing,Failure Analysis,Composites,Coating,Surface Engineering Tribology,Microcontrollers,Tracking,Friction,Wear Testing,Reactors,Detection Nanoindentation,Lubrication,Extrusion,Contact Mechanics,Polyesters,Lubrication Science Tribocorrosion,Tribometry and Lubricants.

Recent Submissions

  • Effect of pineapple leaf (PALF), napier, and hemp fibres as filler on the scratch resistance of epoxy composites 

    Mohd Ridzuan, Mohd Jamir; Mohd Shukry, Abdul Majid; Azduwin, Khasri; E.H.D. Gan; Zuradzman, Mohamad Razlan‬; S., Syahrullail (Elsevier, 2019)
    This article presents the effects of pineapple leaf (PALF), napier, and hemp fibres as filler on the scratch resistance of epoxy composites. In particular, it explores the effect of these natural fillers on the horizontal ...

  • An experimental investigation of palm pressed fibre waste as lubricant in strip drawing 

    Mohd Hafis, Sulaiman; Mohd Ridzuan, Mohd Jamir; Alina Rahayu, Mohamed; N. Farahana, R.; Syahrullail, Samion, Assoc. Prof. Dr. (Penerbit UTM Press, 2014)
    The abundance of palm pressed fibre (PPF) biomass waste generates greenhouse gases. Therefore, an experimental study on catalytic pyrolysis technology using a tubular reactor on PPF oil was performed at temperature of 450 ...

  • Performance of thermoelectric cooling system: effect of aluminium heat sink and heat dissipation 

    Mohd Hafis, Sulaiman; Mohd Ridzuan, Mohd Jamir; Ahmad Firdaus, Ahmad Zaidi; Mohammad Shahril, Salim; Nur Farahana, Ramli; Cheong, Chee Kin (Trans Tech Publications, 2014)
    This paper presents theoretical and experimental research works on the effect of aluminium heat sink and heat dissipation in a portable thermoelectric (TE) cooling system. In this study, three units of TE modules were ...

  • Identification of limiting friction coefficient towards improved hip prostheses 

    Mohd Hafis, Sulaiman; Nur Farahana, Ramli; Mohd Ridzuan, Mohd Jamir; Siti Mahani, Said (Trans Tech Publications, 2013)
    Wear generated by the presence of friction on hip joint contact surfaces can cause debris, which may lead to loosening and failure of the hip prostheses. The objective of this study is to examine the limiting friction ...

  • Optimal coefficient of friction onartificial knee joint contact surfaces 

    Mohd Hafis, Sulaiman; Nur Farahana, Ramli; Mohd Ridzuan, Mohd Jamir; Nur Adlina, Mohd Takhiudin (Trans Tech Publications, 2013)
    Wear generated by the presence of frictiononknee joint contact surfaces can cause debris, which may lead to failure of the artificial knee joint. In this study, the effects of friction coefficients occur on the knee joint ...

  • Design and development of tracking system for mines detector robot 

    Ahmad Firdaus, Ahamad Zaidi; Ng Shao, Liang; Mohd Hafis, Sulaiman; Mohd Ridzuan, Mohd Jamir; Nur Hidayah, Ahmad Zaidi (Trans Tech Publications, 2014-01)
    This paper presents the design and development of tracking system for the mines detector robot. The scope for the tracking system covers two important tasks: 1. Design of optimum tracking path to cover maximum scanning ...

  • Effect of surface roughness of pure aluminium A1100 on the cold work extrusion by using different angles of taper die 

    Mohd Ridzuan, Mohd Jamir; Mohd Hafis, Sulaiman; Azduwin, Khasri; Alina Rahayu, Mohamed; N. Fitriah, Suhaimi; Mohd Shahril, Shariff (Trans Tech Publications, 2014-01)
    The study presented in this paper is focused on the effect of surfaces roughness of pure aluminium A1100 on the cold work extrusion process by three different angles of taper die. Different angles of taper die will affect ...

  • Paraffinic mineral oil lubrication for cold forward extrusion: Effect of lubricant quantity and friction 

    Mohd Hafis, Sulaiman; Mohd Ridzuan, Mohd Jamir; Nur Farahana, Ramli; Syahrullail, Samion (Elsevier Ltd., 2013)
    In this paper, Finite Element (FE) and experimental analyses have been developed on the deformation of aluminium billet over a tool. Effect of friction resulted from the use of additive-free ISO460-compliant paraffinic ...

  • Effect of extrusion ratio on paraffinic mineral oil lubricant in cold forward extrusion 

    Mohd Hafis, Sulaiman; Mohd Ridzuan, Mohd Jamir; Imaduddin Helmi, Wan Nordin; Syahrullail, Samion, Dr. (American Institute of Physics, 2012)
    A finite element (FE) analysis is made for steady-state two-dimensional forward extrusion with three different extrusion ratio values. Predicting extrusion force of aluminum billet extruded with palm oil lubricant will ...

  • Load-displacement behavior of RBD palm stearin oil lubricant quantity in cold extrusion 

    Mohd Hafis, Sulaiman; Mohd Ridzuan, Mohd Jamir; Mohd Afendi, Rojan; Imaduddin Helmi, Wan Nordin; Boon, Raymond Whee Heng; Syahrullail, Samion, Dr. (Universiti Malaysia Perlis (UniMAP)Pusat Pengajian Kejuruteraan Mekatronik, 2012-02-27)
    Large consumption of lubricant may affect the environment due to their high potential of pollution. Therefore, there is significant demand to provide a solution to this current condition by using alternative lubricant ...