Browsing Zuraidah Mohd Zain,Prof Datin Dr. by Title

Now showing items 16-24 of 24

    • Optimization of multi-tool machining processes with simultaneous action 

      Usubamatov, Ryspek; Zuraidah, Mohd Zain; Sin, Tan Chan; Kapaeva, S. (Springer-Verlag, 2016-02)
      The optimization of machining parameters for machine tools using the criterion of maximum productivity rate is complex and, in many cases, an unresolved issue. The intensification of machining processes leads to changes ...

    • Optimization of the processing mode of machine tools by using the criterion of minimum cost 

      A. M., Ahmed Alwaise; Usubamatov, Ryspek, Prof. Dr.; Zuraidah, Mohd Zain, Prof. Dr. (Universiti Malaysia Perlis (UniMAP)Pusat Pengajian Kejuruteraan Mekatronik, 2012-02-27)
      Calculation of the cost and optimization of the operating modes for automatic machine tools today is complex, and in many cases, an unresolved problem. Most equations for calculating the optimal machining processes with ...

    • Productivity and optimization of section-based automated lines of parallel-serial structure with embedded buffers 

      Usubamatov, Ryspek, Prof. Dr.; A. M., Ahmed Alwaise; Zuraidah, Mohd Zain, Prof. Dr. (Springer-Verlag London Limited, 2013-03)
      Automated production lines of a parallel-serial structure are most productive in the manufacturing area. Designers of automated lines segment into sections with several stations place buffers between the series of sections ...

    • Reduction of rejection rate for high gloss plastics product using six sigma method 

      Che Ku Kairulazam, Che Ku Abdullah; Mohd Sabri, Hussin; Zuraidah, Mohd Zain; Nabilah Aminah, Lutpi (Trans Tech Publications, 2014)
      High gloss plastics part in injection molding industries are widely used in Malaysia. However the high rejection rate in this industries were major problem affecting the economic aspects. This paper presents an approach ...

    • Root causes analysis of disbonds and unidentifiable ultrasonic indications on composite materials 

      Muhammad Iqbal, Muhammad Hussain, Dr.; Zuraidah Mohd Zain, Prof. Dr.; Tee, Lei Kee (Trans Tech Publications, 2014)
      To ensure the structural integrity of composite materials, honeycomb sandwich panels must be inspected for defects with through-transmission ultrasonic testing. This study focused on the root causes analysis of disbonds ...

    • South East Asia work measurement practices challenges and case study 

      Thong, Sze Yee; Zuraidah Mohd Zain, Prof. Dr.; Bhuvenesh, Rajamony, Assoc. Prof. Dr. (Springer Science+Business Media Singapore, 2013-07-18)
      South-East-Asia has been producing wide range of products since decades ago, and hence it is often dubbed as the world’s manufacturing-hub. In terms of operation, physical size and capital investment, there are ...

    • Statistical Design of Experiment (SDE): A part of virtual manufacturing 

      Muhammad Iqbal, Muhammad Hussain, Dr.; Zuraidah, Mohd Zain, Prof. Dr.; Mohd Shuid, Salleh (2006)
      Of late, much has been discussed on virtual manufacturing. Essentially, virtual manufacturing comprises of the development of prototypes using computer simulation. In this paper, it is proposed that Statistical Design ...

    • Using quality tools to reduce surface depression defect on composite panels 

      Muhammad Iqbal, Muhammad Hussain, Dr.; Zuraidah, Mohd Zain, Prof. Dr.; Khairul Bakhtiar, Baharim (2010)
      Not available

    • Y-Thompson regulating control using adaptive predictive fuzzy logic for a micro-satellite 

      Nagarajan, Ragunathan; Paulraj, Murugesa Pandiyan, Assoc. Prof.; Sazali, Yaacob, Prof. Dr.; Zuraidah, Mohd Zain, Prof. Dr.; Hoh, W. S. K.; Arshad, A. S. (Institute of Electrical and Elctronics Engineering (IEEE), 2009-03-06)
      Attitude control system is designed to change the attitude of a satellite, able to meet pointing requirement, eliminating external disturbances, a low-cost controller as well as a high reliability control system which can ...