Browsing Final Year Project Papers & Reports by Title
Now showing items 1144-1163 of 2200
-
Influence of leachate contaminants on setting and hardening of concrete
(Universiti Malaysia Perlis (UniMAP)School of Environmental Engineering, 2011-04)One of the major environmental concerns associated with landfilling of municipal solid wastes is related to the discharge of leachate into the environment, which may cause serious pollution to groundwater aquifers as ... -
Influence of metrological factors on variations of particulate matter (PM10) concentration during haze episodes in Malaysia
(Universiti Malaysia Perlis (UniMAP)School of Environmental Engineering, 2015-06)Particulate matter (PM10) is one of the major problems of air pollution around the world due to its ability to cause the adverse effect to environment and human health. Therefore, it is very important to develop PM10 ... -
Influence of mineral additions on the Recycled Aggregate Concrete
(Universiti Malaysia Perlis (UniMAP)School of Environmental Engineering, 2011-05)Used of Recycled Aggregate (RA) in concrete can be described in environmental protection and economical terms. The application of recycled aggregate to use in construction activities have been practice by developed European ... -
Influence of Nitric acid and RE-OA-H3PO4 acid solution on formation of porous anodic aluminium oxide (AAO) thin film
(Universiti Malaysia PerlisSchool of Materials Engineering, 2008-04)Anodizing is very suitable process in formation of porous AAO thin film. By controlling the anodizing parameters such as voltage, time, temperature and acid solution during the anodizing process, a layer of AAO thin film ... -
Influence of soft clay on slope stability
(Universiti Malaysia Perlis (UniMAP)School of Environmental Engineering, 2014-06)Slope stability is a very important on the design of a slope. If this taken lightly by the engineer, perhaps a major disaster will occur that will result in lost lives. Each engineer is responsible to evaluate all aspects ... -
Influence of surface treatment on the properties of high density polyethylene composites filled with palm kernel shell
(Universiti Malaysia Perlis (UniMAP)School of Materials Engineering, 2016-06)The high density polyethylene (HDPE) composites filled with palm kernel shell (PKS) were prepared using Z-blade mixer at processing temperature 190 ˚C and rotor speed 30 rpm. The effect of filler loading of PKS on ... -
The influence of Symmetrical Pulsating AC power input to the efficiency of a single phase transformer
(School of Electrical Systems Engineering, 2007-05)This final year project is to describe about the influence of symmetrical pulsating AC power input to the efficiency of a single phase transformer. In this work, the efficiency of transformer is determined by measuring the ... -
Influence of temperature on reduction behaviour of iron ore-coal composite pellets
(Universiti Malaysia Perlis (UniMAP)School of Materials Engineering, 2016-06)This present study investigated about influence of temperature on reduction behaviour in iron ore and coal composite pellet. The objectives about this research were to analyse the reduction behaviour between iron ore and ... -
The influence of the accelerating voltages on the growth of the square structure during Electron Beam Induced Deposition (EBID) method
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)Electron beam induced deposition (EBID) is a method for high-resolution direct material deposition from the gas phase in the Scanning Electron Microscopy (SEM) onto a substrate. In this project, EBID method has been used ... -
The influence of unsymmetrical AC power input to the core loss of a single phase transformer
(School of Electrical Systems Engineering, 2007-04)This final year project describes about the influence of unsymmetrical AC power input to the core loss of a single phase transformer. The unsymmetrical ac voltage is generated using unidirectional (half wave) ac voltage ... -
The influence of welding parameters and corrosive environment on the joint strength of resistance spot-welded mild steel sheets
(Universiti Malaysia PerlisSchool of Materials Engineering, 2008-04)In the present work, mild steel sheets consisting two batches were welded by resistance spot welding at different welding parameters and exposed under different environments. The 5% sodium chloride brine was used in the ... -
Influence treatment time of lanthanum conversion coating on magnesium alloy
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)This final report consists of several key sections, which are: introduction, problem faced, method of solution, result, discussion and conclusion. Introduction of project described briefly about the material used that is ... -
Influences of Phosphoric acid (H3PO4) solution on formation of Porous Anodic Aluminum Oxide (AAO) thin film
(Universiti Malaysia PerlisSchool of Materials Engineering, 2008-04)The main objective of this study is to analyze the effect of anodizing parameter focusing on anodizing voltage and phosphoric acid (H3PO4) concentration on the formation of porous anodic aluminum oxide (AAO) film. The ... -
Inform departure and arriving of busses using Bluetooth
(Universiti Malaysia PerlisSchool of Computer and Communication Engineering, 2007-03)Bluetooth is a new technology in the wireless communication system. Bluetooth become the best technology that work in short range and using low power comsumption to work. Because of its low power consumption and ability, ... -
Information of face & palmpront multimodal biometric
(Universiti Malaysia Perlis (UniMAP)School of Computer and Communication Engineering, 2015-06)Multimodal Biometrics is a system that are capable of using more than one physiological characteristic for verification or identification. It also refer to the automatic identification or verification of an individual. ... -
Infrared collision avoidance mobile robot
(Universiti Malaysia Perlis (UniMAP)School of Electrical System Engineering, 2011-05)Sensors nowadays are one of the main parts in the development of robot. There are many types of sensors which usually used to accomplish different function by applying different measurement techniques, and using different ... -
Infrared wireless computer peripheral
(Universiti Malaysia PerlisSchool of Computer and Communication Engineering, 2007-03)Overall of the project being done is the implementation of infrared photodiode towards conventional computer peripheral device for mouse keyboard and printer. The transmission of the infrared photodiode is mainly dependant ... -
Insect repellent properties of Melaleuca alternifolia (Tea Tree) in Perlis
(Universiti Malaysia Perlis (UniMAP)School of Bioprocess Engineering, 2016-06)Today, pest problem becomes more serious and it is one of the disaster to farmer in which farming is their way to get many for live. Therefore, a research have been done in which use of plant-based insect repellent. This ... -
Inspect species recognition featuring projection-based shape descriptor
(Universiti Malaysia Perlis (UniMAP)School of Computer and Communication Engineering, 2015-06)This paper proposes an automated system for recognizing insect species based on their shape. In this report, a Radon Transform shape descriptor is proposed to extract a projection according to a single angle. This projection ... -
Integrated constructed wetland system for aquaculture wastewater treatment using wetland plants
(Universiti Malaysia PerlisSchool of Bioprocess Engineering, 2011-05)Aquaculture industry is one of the industries that important to the user. In this industry, there is one major problem, wastewater. Aquaculture wastewaters normally contain high Nitrate, Chemical Oxygen Demand (COD), ...