Browsing School of Manufacturing Engineering (Articles) by Title
Now showing items 11-30 of 125
-
Catalytic combustion system for use in Malaysia small gas turbine: A feasibility study
(Praise Worthy Prize S.r.l., 2011-01)Nowadays, the rates of air pollutant produced by small gas turbine in manufacturing and automobile industries increased continuously. Besides that, the uncontrolled rate of emissions released into the ambient air could ... -
Characteristic and corrosion studies of rare earth (REE) based anodizing on AZ91D magnesium alloy
(Trans Tech Publications, 2014-01)Oxide coatings on AZ91D magnesium alloy were prepared using anodizing technique with 10mA/cm2 current density for 5 minutes in electrolyte containing Mg (NO₃)₂ with NaVO₃ as an additive. The corrosion behaviors of different ... -
Characteristics of Fe-yttria composites fabricated by powder metallurgy method
(Trans Tech Publications, 2013)This study is focused on fabricating and characterizing iron (Fe) composites prepared by powder metallurgy route reinforced with varying weight of Yttria (Y2O3). Composites were prepared based on 5 wt. % to 15 wt. % of ... -
Characterization of PM Fe-Cr-Y₂O₃ composites prepared by microwave sintering technology
(Trans Tech Publications, 2014-01)This research is focused on assessing the feasibility of the new and innovative microwave sintering technology for fabricating iron-chromium composites prepared via powder metallurgy route. Accordingly, the microwave ... -
Chip formation studies in machining fibre reinforced polymer composites
(Inderscience Enterprises Ltd., 2013)The use of end milling process for machining of fibre reinforced polymer composites has been widespread in various industries. Until recently, very little work has been reported with regard to characterisation of chip ... -
Classroom comfort ability assessment: A case study
(Praise Worthy Prize S.r.l., 2012-03)his study was conducted to evaluate the comfort level of an air-conditioned classroom at the School of Manufacturing Engineering campus using objective measurement, subjective assessment and Computational Fluid Dynamics ... -
Combustor aerodynamic using radial swirler
(Academic Journals, 2011-07)A study has been conducted to investigate the flow pattern in a gas turbine combustion chamber by simulation and experimental approaches. Flow pattern inside a combustor is important to self sustain the flame, increase ... -
Comparison between ANSYS and CATIA simulation capability in simulating round shape diaphragm of MEMS piezoresistive pressure sensor
(Institute of Electrical and Electronics Engineering (IEEE), 2007-11)This paper presents a comparative study of MEMS Piezoresistive Pressure Sensor simulation using two different software of ANSYS and CATIA respectively. It is aimed to investigate the feasibility of utilizing CATIA software ... -
Comparison between single and multi gates for minimization of warpage using taguchi method in injection molding process for ABS material
(Trans Tech Publications, 2013-12)In this study, a mold is designed in single and dual type of gate in order to investigate the deflection of warpage for thick component in injection molding process. Autodesk Moldflow Insight software was used as a medium ... -
Comparison study in consolidation of yttria reinforced iron-chromium composites using conventional and microwave sintering technique
(Trans Tech Publications, 2014)This research is focused on studying the density and mechanical properties of iron-chromium composites consolidated by innovative rapid microwave sintering technology against conventionally sintered counterparts using slow ... -
Convergence of finite element model for crushing of a conical thin-walled tube
(Elsevier B.V., 2013)In this paper, a convergence of finite element model using different types and sizes of mesh modes has been conducted. A thin-walled conical tube was modeled using plane shell element in LS-DYNA software under dynamic axial ... -
Design and analysis of magnetic flux leakage capsule
(International Frequency Sensor Association (IFSA), 2013-08)Magnetic flux leakage (MFL) is among the current in-line non-invasive popular technique applied in pipeline condition control and monitoring. This paper discussed on the design and development of magnetic flux leakage ... -
Design and anaysis of thermoacoustic air conditioning system as environmental friendly device
(Trans Tech Publications, 2012-02)Thermoacoustic air conditioning system is a new technology design of cooling system which offers the possibility for simple and efficient energy conversion devices. This research is looking an alternative for CFC-contained ... -
Design and fabrication of a die for molding test press.
(Praise Worthy Prize S.r.l., 2012)This project aims to design and fabricate an die for molding test press. Mold Test Press Machine uses the concept of Compression Molding/Hot Press Molding. This project will be handled from the beginning of the design until ... -
Design of fuzzy logic model for the prediction of tool performance during machining of composite materials
(Elsevier, 2012)Complexity of the machining process, the nonlinear relationship between parameters, and the random variations of material properties make the prediction of tool life during machining of composite material a challenge. ... -
Development of gas turbine spray test rig for biofuel
(Praise Worthy Prize S.r.l., 2011-01)The design of the fuel supply system to be used for biofuel is one of the systems that are complicated to design. As this system involves a lot of components, all the components in this design play an important role to ... -
Development of improved bottleneck-based heuristic for re-entrant flow shop with dominant machine at M1 and M4
(Praise Worthy Prize S.r.l., 2012-03)This project investigates the possibility of developing scheduling heuristic using bottleneck approach for a four machine permutation re-entrant flow shop with the process routing of M1,M2,M3,M4,M3,M4 where M1 and M4 have ... -
Development of palm oil based bio-product industrial wax and its application performance study
(David Publishing, 2010-06)Machining is a mechanical process where excess material from a work is removed to produce a product. At the moment different ferrous, non-ferrous materials and industrial blue wax have been used for prototype models. ... -
Effect of drill point angle on surface integrity when drilling titanium alloy
(Trans Tech Publications, 2014)Surface integrity of machined component is of major importance for the reliability and safety requirements during in service especially for the aerospace applications. This paper presents an investigation on the effect of ...