This page provides access to research works by Ts. Dr. Zainon, currently a Lecturer of School of Manufacturing Engineering, Universiti Malaysia Perlis.

News

Skills and Expertise: Quality Management, Control Engineering, Lean Manufacturing, Machine Design, and Vibration Control and Analysis

Recent Submissions

  • Review on non uniform rational B-spline (NURBS): concept and optimization 

    Munira, Mohd Ali; Nur Najmiyah, Jaafar; Fazilah, Abdul Aziz; Nooraizedfiza, Zainon (Trans Tech Publications, 2014-02)
    This paper is to provide literature review of the Non Uniform Rational B-Splines (NURBS) formulation in the curve and surface constructions. NURBS curves and surfaces have a wide application in Computer Aided Geometry ...
  • Application of Chemical Health Risk Assessment (CHRA) in an industry 

    Nooraizedfiza, Zainon; Mohd. Fathullah, Ghazli @ Ghazali (Universiti Malaysia Perlis (UniMAP), 2009-12-01)
    Occupational Safety and Health (Use and Standards of Exposure of Chemicals Hazardous to Health) Regulation 2000 requires Chemical Health Risk Assessment (CHRA) to be carried out at all work places where chemical been ...
  • Anthropometry data for 4th year UniMAP student 

    Nooraizedfiza, Zainon; Zakaria, S.; Mokhtar, Mat Salleh; Mohd. Fathullah, Ghazli @ Ghazali (Universiti Malaysia Perlis (UniMAP), 2009-12-01)
    Anthropometry is a science of measurements and the art of application that establishes the physical geometry, mass properties, and strength capabilities of the human bodies. This paper was taken out from laboratory session ...
  • Improving warpage on thin shallow parts in two-plate moulds with conformal cooling channels 

    Shayfull Zamree, Abd. Rahim; Muhammad Syahril, Bahari; Siti Aishah, Adam; Mohd. Nasir, Mat Saad; Nooraizedfiza, Zainon (Praise Worthy Prize S.r.l., 2013-03)
    Nowadays, the trend of consumer products designed is getting smaller and most of cover is made from plastic which was produced by using injection molding process. Thus, the demand of thin shallow plastic parts in global ...
  • The effect of shear rate and temperature on rheology properties of magnesium metal injection molding feedstock 

    Nooraizedfiza, Zainon; Salmah, Husseinsyah, Prof. Madya Ir. Dr.; Omar, Mustapha A. (Praise Worthy Prize S.r.l., 2013-11)
    Metal injection molding (MIM) becomes a well-established and promising technology for small and mass production. Feedstock characterization is one of the most important roles in ensuring the properties of the MIM products. ...
  • Comparison study in consolidation of yttria reinforced iron-chromium composites using conventional and microwave sintering technique 

    Marina, Marzuki; Mohd Zamzuri, Mohammad Zain; Mohd Nazree, Derman, Dr.; Mohd Asri, Selamat; Nooraizedfiza, Zainon (Trans Tech Publications, 2014)
    This research is focused on studying the density and mechanical properties of iron-chromium composites consolidated by innovative rapid microwave sintering technology against conventionally sintered counterparts using slow ...
  • Characterization of PM Fe-Cr-Y₂O₃ composites prepared by microwave sintering technology 

    Marina, Marzuki; Mohd Zamzuri, Mohammad Zain; Mohd Nazree, Derman, Dr.; Mohd Asri, Selamat; Wan Abdul Rahman Assyahid, Wan Ibrahim; Nooraizedfiza, Zainon (Trans Tech Publications, 2014-01)
    This research is focused on assessing the feasibility of the new and innovative microwave sintering technology for fabricating iron-chromium composites prepared via powder metallurgy route. Accordingly, the microwave ...
  • Improvement of corrosion resistance of rare earth element (REE)-based anodic oxidation coating on AZ91D magnesium alloy 

    Mohd. Zamzuri, Mohammad Zain; Suhaimi, Illias; Mokhtar, Mat Salleh; Khairul Azwan, Ismail, Dr.; Nooraizedfiza, Zainon (Trans Tech Publications, 2012)
    Anodization is a useful technique for forming protective films on magnesium alloys and improves its corrosion resistance. Based on the rare earth metal (REE) salt solution, the optimum parameter was selected by comparing ...
  • Warpage optimization on ultra thin plate in three plate mold for PP, ABS & ABS+PC materials by using Taguchi method 

    Mohd. Nasir, Mat Saad; Norshah Afizi, Shuaib; Shayfull Zamree, Abd. Rahim; Mohd. Fathullah, Ghazli @ Ghazali; Nooraizedfiza, Zainon (Praise Worthy Prize S.r.l., 2012-03)
    The parameters setting of process conditions in injection molding process is very importance to ensure the quality of molded components is controlled by minimizing of any defects such as warpage. Various injection parameters ...
  • Improvement of Corrosion Resistance of Rare Earth Element (REE)-Based Anodic Oxidation Coating on AZ91D Magnesium Alloy 

    Mohd Zamzuri, Mohammad Zain; Suhaimi, Illias; Mokhtar, Mat Salleh; Khairul Azwan, Ismail; Nooraizedfiza, Zainon (Scientific.net, 2012-06-26)
    Anodization is a useful technique for forming protective films on magnesium alloys and improves its corrosion resistance. Based on the rare earth metal (REE) salt solution, the optimum parameter was selected by comparing ...
  • Characteristics of Fe-yttria composites fabricated by powder metallurgy method 

    Marina, Marzuki; Kartini, Alir; Wan Abdul Rahman Assyahid, Wan Ibrahim; Nooraizedfiza, Zainon; Mohd Asri, Selamat; Mohd Zamzuri, Mohammad Zain (Trans Tech Publications, 2013)
    This study is focused on fabricating and characterizing iron (Fe) composites prepared by powder metallurgy route reinforced with varying weight of Yttria (Y2O3). Composites were prepared based on 5 wt. % to 15 wt. % of ...
  • Relationships validation between KPOV and KPIV using hypothesis tests 

    Nooraizedfiza, Zainon; Mohd Zamzuri, Mohammad Zain (Universiti Malaysia Perlis (UniMAP)Institut Matematik Kejuruteraan, 2010-06-02)
    Hypothesis tests are procedures for making rational decisions about the reality of effects. The objective of this paper was to determine the relationships between Key Process Output Variables (KPOV) and Key Process Input ...