Browsing Mazlee Mohd Noor, Assoc. Prof. Dr. by Title
Now showing items 22-41 of 41
-
Fabrication and characterization of porous F-75 for potential application in tissue engineering
(Trans Tech Publications, 2013)Porous F-75 (Co-Cr-Mo) was produced by powder metallurgy technique. F-75 powder was mixed with space holder and compacted using different pressures (300 MPa, 350 MPa, 400 MPa, 450 MPa). The green samples were sintered at ... -
Failure investigation on rusty mesh strainer of petrochemical plant
(Trans Tech Publications, 2013)The wire material of filter mesh is made of 304 grade stainless steel. The failure to run properly was due to the impact of burst and torn. The client also expects that the failure was due to corrosion problems. A visual ... -
Fly ash as Sand Replacement Material (SRM) in the development of composite cement: Physical and mechanical properties
(Universiti Malaysia Perlis (UniMAP), 2012-06-18)There has been vast research enhancing the usage of industrial wastes in engineering applications. This research paper reports the effect of fly ash on the physical and mechanical properties of composite cement. Fly ash ... -
Mechanical properties and fracture behaviour of coconut fibre-based green composites
(Foundation for Materials Science and Engineering “Serban Solacolu”, 2012)This paper presents the influence of natural fibre content on the mechanical properties of coconut fibre based-green composites. The mixture ratio of cement:sand by weight was fixed at 1:1. Coconut fibre was used as ... -
Mechanical properties of dissimilar welds between stainless steel and mild steel
(Trans Tech Publications, 2013)Joining of stainless steel type 304 to mild steel was carried out using a gas tungsten arc welding (GTAW). Samples were welded using stainless steel welding electrode: (AWS: E308l-16) and mild steel welding electrode: (AWS: ... -
Metal Implant
(Malaysian Invention and Design Society (MINDS), 2006-05-19)This research product is cobalt-chromium metal implant produced by powder metallurgy technique. -
The Microsructure and Properties of Aluminium Composite Reinforced with 65 μm Alumina Particles via Powder Metallurgy
(Universiti Malaysia Perlis (UniMAP), 2007-06-09)This article will report the effect of weight percentage on the microstructure and properties of alumina particle reinforced aluminum metal matrix composite. This involved fabrication of aluminum composite via powder ... -
Microstructural study and differential scanning alorimetry analysis at elevated temperatures of uperheated as-cast A357 alloy
(University of Malaya, 2009)The microstructure of superheated as-cast A357 alloy has been analysed to study the solidification structures of α-Al dendrites, eutectic Si particles and intermetallic compounds at different sections of the specimen. The ... -
Microstructural study and differential scanning Calorimetry analysis at elevated tempatures of superhead As-Cast A357 alloy
(Universiti Kebangsaan Malaysia (UKM), 2008-12-03)The microstructure of superheated as-cast A357 alloy has been analysed to study the solidification structures of α-Al dendrites, eutectic Si particles and intermetallic compounds at different sections of the specimen. ... -
Microstructural study of Al-Si-Mg alloy reinforced with stainless steel wires composite via casting technique
(Science Publications, 2008)The microstructural study of Al-Si-Mg alloy reinforced with stainless steel wires (Al-Si-Mg/SSw) has been investigated and focused on the both microstructures in the matrix and near to the interface and also the wetting ... -
Microstructure, Properties and Fracture Mechanism of Al 2014 Reinforced with Alumina Particles
(Kolej Universiti Kejuruteraan Utara Malaysia, 2004)The studies of microstructure, properties and fracture mechanism have been conducted on Al 2014 matrix alloy reinforced with 10 volume percent (Composite 1) and 15 volume percent (Composite 2) of alumina (Al2O3) particles ... -
Microwave sintering of pure iron with addition of stearic acid as binder
(Trans Tech Publications, 2012)The purpose of this study is to investigate the effect of the stearic acid as binder in sintering pure iron using a microwave furnace. The study was focused in mechanical properties such as porosity, density and micro-hardness ... -
Optimization of sintering temperature on microwave sintering of the composite iron-chromium reinforced with alumina particles
(Trans Tech Publications, 2014-01)Microwave sintering technology has become attractive and gained interest among material researchers due its capability and advantages over conventional sintering. Since two decades ago, intensive researches on microwave ... -
Potentiodynamic polarization of Mg-0.22ca alloys containing minor element of Aluminium
(Universiti Malaysia Perlis, 2009-12-01)Mg alloys played a significant role in replacing the existing sacrificial anodes. To maintain the negative potential and its capability in preventing corrosion, Ca and Al was added as alloying elements. Polarization curves ... -
Preliminary Microstructure and Hardness Studies of A356/Stainless Steel Composite via Gravity Die Casting Technique
(Universiti Malaysia Perlis (UniMAP), 2007-06-09)The microstructure and hardness of A356/stainless steel composite via gravity die casting technique were evaluated. Both nearly completed bonding and incomplete bonding was seen at the stainless steel wire- A356 matrix ... -
Recycled Aluminium Composite Pulley
(Malaysian Invention & Design Society (MINDS), 2006-05-19)Recycle Aluminium Composite Pulley was an environmental-friendly pulley from innovative recycle aluminium composite materials. This pulley was fabricated by using recycled aluminium alloy from automotive component reinforced ... -
Sand replacement materials (SRM) in sustainable cement composites; A concise review
(Trans Tech Publications, 2013)This paper presents a short review of research works on the development of sustainable cementitious matrix composites with addition of potential mineral wastes as sand replacement materials. The study emphasizes on the ... -
Static X-ray scans on the titanium hydride (TiH2) powder during dehydrogenation
(Trans Tech Publications, 2013)This work investigates the dehydrogenation of TiH2 powder during isothermal heating at 600°C using the static x-ray scans of high temperature x-ray diffraction (XRD). As-received TiH2 powder with a particle size of 5 μm ... -
Sustainable porous materials for gas adsorption applications; A concise review
(Trans Tech Publications, 2013)Many new sustainable porous materials were developed for gas adsorption applications. Common materials such as activated carbon, clay materials and metal organic framework (MOF) that utilized as potential porous adsorption ...