Search
Now showing items 1-10 of 14
Effect of Compatibilizer on Mechanical Properties and Morphology of Clay Filled Low Density Polyethylene (LDPE) Composites
(Universiti Malaysia Perlis (UniMAP), 2007-06-09)
The main purpose of incorporating fillers, such as clay into composites of polyolefin is to decrease costs and change the properties. Structural differences between both components give rise to the formation of large filler ...
The Effect of Porosity on Thermal Conductivity of Silicon Carbide Filled Polyproplyene Composite
(Universiti Malaysia Perlis (UniMAP), 2007-06-09)
Silicon carbide filled Polypropylene (PP) composites are fabricated, where the compounding is carried out by using Z-blade mixer with filler loadings of 0wt%, 10wt%, 20wt% and 30wt%. Composite sheets produced from hot press ...
Effect of Particle Coating on Matrix-Reinforcement Bonding
(Universiti Malaysia Perlis (UniMAP), 2007-06-09)
A crucial step in the liquid state processing of particulates reinforced metal matrix composites is the incorporation of the ceramic particles into molten matrix alloy. The development of SiO2 coating on fly
ash particles ...
Microstructure characterization of Al/Calcined Dolomite Metal Matrix Composites
(Universiti Malaysia Perlis (UniMAP), 2007-06-09)
Al/calcined dolomite metal-matrix composites (MMC) were fabricated and tested by varies the calcined dolomite content (10-30 wt%) and using unidirection compaction and sintering as consolidation method. Upon incorporation ...
Physical properties of Al/Calcined Dolomite Metal Matrix composite by Powder Metallurgy Route
(Universiti Malaysia Perlis (UniMAP), 2007-06-09)
Calcined dolomite is dolomite powder that had been calcined at high temperature. This paper describes the fabrication of aluminum metal matrix composite reinforced with calcined dolomite by powder metallurgy route. The ...
Corrosion behaviour of Anodised PM Aluminium Matrix Composite Reinforced with 15 wt % Saffil Alumina short fibre
(Universiti Putra Malaysia, 2007)
A study of corrosion behaviour on anodised PM aluminium matrix composites (AMC) reinforced with Saffil™ alumina short fibre was done. AMC was fabricated by powder metallurgy methods (PM) with using Al flake powders and ...
The effect of compatibilizer on tensile properties, swelling behaviour and morphology of Calcium Carbonate filled Polypropylene/Ethylene Propylene Diene Terpolymer composites
(Universiti Kuala Lumpur (UniKL), 2007-11-27)
Calcium carbonate (CaCO3) was used as filler in the polypropylene (PP)/ ethylene propylene diene terpolymer (EPDM) composites in order to decrease cost and change the properties. The composites were prepared by using a ...
Study of wear on anodised PM Aluminium Matrix composite reinforced with 15 wt % Saffil Alumina Short Fibre
(Universiti Malaysia Perlis, 2007-06-09)
A study of wear behaviour on anodised powder metallurgy aluminium matrix composites (PM AMC) reinforced with Saffil™ alumina short fibres was done. AMC was fabricated by powder metallurgy methods (PM) with using Al flake ...
Mechanical and Morphology Properties of Egg-Shell Powder (ESP) Filled Low Density Polyethylene Composites
(Universiti Kuala Lumpur (UniKL), 2007-11-27)
Mechanical and morphology properties of low density polyethylene/egg shell powder composites were examined. Composites were prepared in Z-Blade Mixer. Mixing was done at 1600C and rotor speed of 50 rpm. Sample of composite ...
The Effect of Coupling Agent on Thermal Properties and Morphology of Paper Sludge Filled Polypropylene (PP)/Ethylene Propylene Diene Terpolymer (EPDM) Composites
(Universiti Malaysia Perlis (UniMAP), 2007-06-09)
The paper sludge was used as a filler in PP/EPDM composites and 3-aminopropyl triethoxysilane (3-APE) was used as a coupling agent in this study. The effects of filler loading and 3-APE on the thermal properties and ...