Browsing Journal Articles by Author "Mazlee, Mohd Noor, Dr."

Now showing items 1-10 of 10

    • Effect of spot welding current and cycles on the mechanical properties of welded galvanized steel sheets 

      Shamsul Baharin,  Jamaludin, Prof. Dr.; Mazlee, Mohd Noor, Dr.; Muhammad Rifki, Ismail; Khairel Rafezi, Ahmad, Dr.; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr. (Trans Tech Publications, 2013)
      Studies on the effects of welding current and cycles were carried on the galvanized steel sheets using spot welding. The welding currents used were 3 kA, 5 kA 6 kA and the welding cycles were 4, 6 and 8. Tensile shear and ...

    • The effects of fly ash and polystyrene bead additions on compressive strength of foamed cement composites 

      Mazlee, Mohd Noor, Dr.; Key, Tan Pei; Shamsul Baharin,  Jamaludin, Prof. Dr.; Roshasmawi, Abdul Wahab; Nur Izzati, Muhd Nadzri; Alida, Abdullah (Trans Tech Publications, 2013)
      The effects of both additions of fly ash and polystyrene (PS) beads were studied on compressive strength of foamed cement composites. The increasing amount of fly ash addition up to 6 wt. % has been found to increase the ...

    • Fabrication and characterization of porous F-75 for potential application in tissue engineering 

      Shamsul Baharin,  Jamaludin, Prof. Dr.; Tan, Wei Leng; Nur Hidayah, Ahmad Zaidi; Zuraidawani, Che Daud; Mazlee, Mohd Noor, Dr. (Trans Tech Publications, 2013)
      Porous F-75 (Co-Cr-Mo) was produced by powder metallurgy technique. F-75 powder was mixed with space holder and compacted using different pressures (300 MPa, 350 MPa, 400 MPa, 450 MPa). The green samples were sintered at ...

    • Mechanical properties of dissimilar welds between stainless steel and mild steel 

      Shamsul Baharin,  Jamaludin, Prof. Dr.; Mazlee, Mohd Noor, Dr.; Shahzan Kamarul, A. Kadir; Khairel Rafezi, Ahmad, Dr. (Trans Tech Publications, 2013)
      Joining of stainless steel type 304 to mild steel was carried out using a gas tungsten arc welding (GTAW). Samples were welded using stainless steel welding electrode: (AWS: E308l-16) and mild steel welding electrode: (AWS: ...

    • Microwave sintering of pure iron with addition of stearic acid as binder 

      Wan Abdul Rahman Assyahid, Wan Ibrahim; Shamsul Baharin, Jamaludin, Prof. Dr.; Mazlee, Mohd Noor, Dr. (Trans Tech Publications, 2012)
      The purpose of this study is to investigate the effect of the stearic acid as binder in sintering pure iron using a microwave furnace. The study was focused in mechanical properties such as porosity, density and micro-hardness ...

    • Optimization of sintering temperature on microwave sintering of the composite iron-chromium reinforced with alumina particles 

      Wan Abdul Rahman Assyahid, Wan Ibrahim; Shamsul Baharin, Jamaludin, Prof. Dr.; Mazlee, Mohd Noor, Dr. (Trans Tech Publications, 2014-01)
      Microwave sintering technology has become attractive and gained interest among material researchers due its capability and advantages over conventional sintering. Since two decades ago, intensive researches on microwave ...

    • The root caused analysis of leakaged heat exchanger tube 

      Shaiful Rizam, Shamsudin; Mohd Arif Anuar, Mohd Salleh; Azmi, Rahmat, Assoc. Prof. Dr.; Mazlee, Mohd Noor, Dr.; Mohd Harun; Hafizal, Yazid (Carl Hanser Verlag GmbH & Co., 2015-03)
      AISI type 316L stainless steel was used as a heat exchanger tube material in an inter-cooler column. After less than a year of operation, severe corrosion failures occurred and a transverse opening leakage was observed on ...

    • Sand replacement materials (SRM) in sustainable cement composites; A concise review 

      Madzura, Mohamad; Mazlee, Mohd Noor, Dr.; Shamsul Baharin,  Jamaludin, Prof. Dr. (Trans Tech Publications, 2013)
      This paper presents a short review of research works on the development of sustainable cementitious matrix composites with addition of potential mineral wastes as sand replacement materials. The study emphasizes on the ...

    • Static X-ray scans on the titanium hydride (TiH2) powder during dehydrogenation 

      Nur Farhana, Hiyazi; Wang, Yu; Mazlee, Mohd Noor, Dr.; Lap, Sammy Ip Chan (Trans Tech Publications, 2013)
      This work investigates the dehydrogenation of TiH2 powder during isothermal heating at 600°C using the static x-ray scans of high temperature x-ray diffraction (XRD). As-received TiH2 powder with a particle size of 5 μm ...

    • Sustainable porous materials for gas adsorption applications; A concise review 

      Wai, Hoong Chan; Mazlee, Mohd Noor, Dr.; Zainal Arifin, Ahmad, Prof.; Shamsul Baharin,  Jamaludin, Prof. Dr.; Mohd Azlan, Mohd Ishak, Prof. Madya Dr; Muhammad Shahar, Jusoh, Dr. (Trans Tech Publications, 2013)
      Many new sustainable porous materials were developed for gas adsorption applications. Common materials such as activated carbon, clay materials and metal organic framework (MOF) that utilized as potential porous adsorption ...