Search
Now showing items 1-10 of 10
Rheological and thermal properties of palm kernel shell filled low density polyethylene composites
(Universiti Malaysia Perlis (UniMAP), 2013)
The palm kernel shell (PKS) filled low density polyethylene (LDPE) composites
were prepared by Z-blade mixer at temperature of 180 °C and rotor speed of 50 rpm.
The effects of PKS loading and different types of chemical ...
Properties of low density polyethylene/natural Rubber/chemical modified water hyacinth fibers (Eichhornia crassipes) composites
(Universiti Malaysia Perlis, 2013)
The natural fiber composites of low density polyethylene (LDPE)/natural rubber
(NR)/water hyacinth fibers (WHF) were studied. The composites were prepared by using
Brabender Plasticorder at 160 oC with rotor speed of 50 ...
Fabrikasi dan penganodan komposit metalurgi serbuk aluminium-magnesium diperkuat gentian pendek alumina saffil
(Universiti Malaysia Perlis (UniMAP), 2013)
Anodising process on powder metallurgy aluminium-magnesium composites reinforced with short fibre alumina SaffilTM has been studied. PM Al-Mg composites were fabricated using PM route with Mg powder as the alloying element ...
Production of fly ash-based geopolymer bricks through geopolymerization process
(Universiti Malaysia Perlis (UniMAP), 2013)
Utilization of fly ash as a raw material for geopolymer brick production seems to be a
logical solution that allows for the conservation of natural resources, abates further
pollution and preserves the environment. Fly ...
Effect of pyrolysis on shrinkage properties of SU-8 polymer
(Universiti Malaysia Perlis (UniMAP), 2013)
Epoxy SU-8 has drawn a lot of attention during the last decades due to its promising
mechanical and electrical properties. Extensive research regarding the mechanical
properties of negative photoresists SU-8 has been ...
Development and characterization of Co-Cr-Mo (F-75 alloy)/hydroxyapatite composites fabricated by powder metallurgy for biomedical applications
(Universiti Malaysia Perlis (UniMAP), 2013)
Co-Cr-Mo (F-75) alloy is known to be used in biomedical field because of their excellent biocompatibility when implanted to human or animal body. Hydroxyapatite (HAP) powders have been used as filler because HAP is the one ...
Sensing properties of chitosan and chitosan-roselle film sensors on toluene concentrations detection
(Universiti Malaysia Perlis (UniMAP), 2013-10)
This study aims to observe the sensing properties of chitosan sensor (CS) and chitosanroselle sensors (CRSs) on toluene at various concentrations. CRSs were deposited using various chitosan: roselle ratio of 99:1 to 89:11 ...
Development of anodised aluminium oxide nanostructure from Al-Mn alloy
(Universiti Malaysia Perlis (UniMAP), 2013)
This study was divided into two parts. The first part of the study was focused on
the synthesis of well ordered porous AAO by using oxide dissolution treatment. The
porous AAO was formed by anodising of 99.99 % aluminium ...
Effect of isothermal aging to the intermetallic compound (IMC) growth of Sn-0.7Cu-1.0Si₃N₄ composite solder on copper substrate
(Universiti Malaysia Perlis (UniMAP), 2013)
The excessive growth of intermetallic compound (IMC) layer on solder joints has
become a challenging to the electronic packaging industry. Excessive IMC growth is a
barrier for the reliability of solder joints and the ...
Development of Lead-Free Sn-0.7Cu-Si3N4 composite solders
(Universiti Malaysia Perlis (UniMAP), 2013)
Lead based solder have been widely used before science have proven lead as one
of the hazardous substances which can harm the environment and human health. With
the banning usage of lead based solder as interconnect, ...