Browsing School of Mechatronic Engineering (FYP) by Issue Date
Now showing items 41-60 of 71
-
The size effect on fatigue strength of mild steel
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)Fatigue evaluates the effects of material shape, surface condition, stress level, material size and related factors on fatigue life of metallic materials. These studies focused on experimental analysis to compare the effect ... -
Characterization of the stent-grafts performance in abdominal aortic aneurysms
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)Since the introduction of endovascular techniques in the early 1990s for the treatment of abdominal aortic aneurysms (AAAs), the insertion of a stent-graft (SG) into the affected artery segment has been greatly successful ... -
Design and analysis of a shell and tube heat exchanger (one shell pass and one tube pass)
(Universiti Malaysia Perlis (UniMAP)School of Mechatronic Engineering, 2009-04)A shell and tube heat exchanger (one shell pass and one tube pass) is a heat exchange device between hot fluid and cold fluid. It is used widely in process industry for cooling, heating and heat exchange stream in ... -
Design of alternative inhaler system to improve the delivery of inhaled pharmaceutical aerosol (IPA)
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)The Metered Dose Inhalers (MDI) is used to prevent and relieve the symptoms and progression of certain diseases (asthma, chronic obstructive pulmonary disease, cystic fibrosis and bronchiectosis) by delivering the Inhaled ... -
Prototype development of micro hydropower house
(Universiti Malaysia Perlis (UniMAP)School of Mechatronic Engineering, 2009-04)Due to the fact that the cost of oil, gas and electricity is increasing, the engineers are urged to find alternative sources of energy. Another reason, which urges them to do so is to reduce the impacts of the environment. ... -
A control system of fan speed controller for inhaler system to improve the delivery of inhaler pharmaceutical aerosol (IPA)
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)Inhaler is one of the medical treatments that can be used to manage asthmatic symptom which is available in market. Pressurized Metered Dose Inhaler (PMDI) is suitable used for asthma patient to prevent and relieve the ... -
Bearing puller design
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)The focus of this project is to design a bearing puller of specific application. This project was assigned to design a bearing puller, a device for removing bearings, gears and countless other press fitted parts from ... -
Heating and cooling analysis of living room
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)This project is about analyzing the heating and cooling condition of a living room. It is divided in to three parts. The first part is the design a model for a living room. The size, material properties and the dimension ... -
Vibration analysis testing in selected vehicle cabin
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)Generally, vibration generated from various sources (engine, road surface, tires, exhaust, etc.) should be considered in the design of a car body. These vibrations travel through transfer systems (drivetrain, suspension, ... -
Condition monitoring on bearing faults of electric motor – Based on vibration signal
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)The condition monitoring of rotating shaft is important in terms of system maintenance and process automation, especially for the bearing which is most common component in machines or apparatuses. In this project, a ... -
The study of material stress concentration
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)In this project, investigation of stress concentration factor is carried out. Some specimens with shoulder fillets and circular holes are involved with the machining process according to the dimensions. An axial force ... -
Testing and analysis of rubber base isolator using scrap tire pads
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)This paper focuses on the experimental studies on the development of low cost seismic base isolation pads using scrap automobile tire pads (STP). The mechanical properties of STP specimens are made from different tire ... -
Condition monitoring on bearing faults of electric motor – Based on sound signal
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-04)The condition monitoring of rotating shaft is important in terms of system maintenance and process automation, especially for the bearing which is most common component in machine or apparatuses. In this project, a general ... -
Experimental analysis of splitting tensile test for brittle material
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-05)In this project, method of dynamic tensile test for brittle material is studied. The tensile test of brittle materials, i.e., ceramic, glass, plaster, concrete, and rock, are relatively difficult to performed in dynamic ... -
Drop simulation of notebook PC
(Universiti Malaysia Perlis (UniMAP)School of Mechatronic Engineering, 2009-05) -
Ratcheting behaviour of aluminum under cyclic axial load
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-05)An experiment about uniaxial ratcheting of Aluminum was investigated and particular attention was paid to ratcheting behavior under different cyclic loading. The effect of amplitude stress and mean stress on the ratcheting ... -
The effect of strain rate of steel material
(Universiti Malaysia Perlis (UniMAP)School of Mechatronics Engineering, 2009-05)This project presents the effect of strain rate of steel material. Two different experiments are required in order to investigate the effect of strain rate of steel material. The first experiment is using Universal Testing ... -
Stress analysis of the connecting rod in the two-stroke combustion engine
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-05)The main objective of this study was to study a stress distribution in finite element analysis (FEA) and buckling of the engine components, particularly the connecting rod in the Two-Stroke Combustion Engine. This has ... -
Prototype development of micro-hydropower house: Testing
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-05)Micro-hydropower system is a division of hydropower system which capable to produce electricity up to 100 kilowatt (kW). Water energy basically produces from flowing water which causes the rotation of a turbine generator. ... -
Designing and simulation of wind turbine blades based on vertical axis wind turbine model
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2009-05)This final year project is to designing and simulation of wind turbine blades based on Vertical Axis Wind Turbine (VAWT) model. The implementation of wind energy conversion systems in the built environment renewed the ...