Browsing School of Manufacturing Engineering (FYP) by Title
Now showing items 196-215 of 336
-
Investigation new sensing SnTiO3 as thin film light sensor
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)In this project, some research has been done on Tin dioxide (SnO2) and stannium titanate perovskite (SnTiO3) thin films. It has been known that tin dioxide has various applications, especially for gas sensor, light sensor, ... -
Investigation of characteristics of powder at press surpasses 3000 ton
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project is carried out to investigate characteristic an iron powder at pressure beyond 3000 tons. The effects of high load and pressure on a compacted powder were investigated. A cube shape was produced using pressing ... -
Investigation of dimensional accuracy and chip formation on peck drilling of mild steel
(Universiti Malaysia Perlis (UniMAP), 2016-05)Drilling process is the most important machining process in the manufacturing industries. Almost all mild steel industries and production are based on drilling process. However, the difficulty of the mild steel machining ... -
Investigation of dimensional accuracy and chip formation on through hole drilling of mild steel
(Universiti Malaysia Perlis (UniMAP), 2016-05)Drilling process is among the last proses in manufacturing were highly focused in the industry due to huge impact on the final product. Therefore, a method for determining appropriate drilling techniques and parameters ... -
Investigation of surface roughness and chip formation on peck drilling of mild steel
(Universiti Malaysia Perlis (UniMAP), 2016-05)Drilling is one of the fundamental machining processes and most frequently performed in the last step of material removal process. Furthermore, the machining parameter has significant influence to the surface finish and ... -
Investigation of tool wear and chip formation on peck drilling of mild steel
(Universiti Malaysia Perlis (UniMAP), 2016-05)In drilling process at the industry, the problem that always emerges is severe wear occurs at cutting tool and poor surface finish on part drilled. This is because of improper selection of cutting parameter that affects ... -
Investigation of tool wear and chip formation on through hole drilling of mild steel
(Universiti Malaysia Perlis (UniMAP), 2016-05)Nowadays, the problem of cutting tool failures becomes important in manufacturing industries. After certain working time at production, tool wear occurs and cutting tool become dull and required a changing. This is because ... -
Investigation of tool wear and chip formation on through hole drilling of mild steel
(Universiti Malaysia Perlis (UniMAP), 2016-06)In drilling process at the industry, the problem that always emerges is severe wear occurs at cutting tool and poor surface finish on workpiece. This is because of improper selection of cutting parameters that affect to ... -
Investigation on Geometric parameter of floating platform movement using air pressure
(Universiti Malaysia Perlis (UniMAP), 2016-05)A floating platform in the air is widely used in the industry nowadays. This platform is used as the transportation medium for some industries or parties. The problem that always occurs for transporting loads previously ... -
An investigation on machinability of aluminium matrix composite
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2009-10) -
Investigation on radial curve vane air swirler to determine the effect on combustion in the combustion chamber that uses butane gas fuel
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)The research is about investigation on radial curve vane air swirler to determine the effect on combustion in the combustion chamber that uses butane gas fuel. Air swirlers with vane angle of 20º and 60º is use to make ... -
Investigations of a part jamming probability into a chute of transport system
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)The main purpose for preparing this report is to record all the progress and results obtained during the period specified to complete this task. Projects handled for both semesters, semesters 1 and 2 2009/2010 are to ... -
Jig design for reduction of assembly cycle time and defect for front panel assembly
(Universiti Malaysia Perlis (UniMAP), 2016-06)Problems that often occur when the assembly process is high assembly time and defect are serious problem that occurs in every production industry. To complete the assembly process of front panel at Wong Engineering the ... -
The landscape lighting using LED
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)This final year project explains how to create a rich landscape lighting using light emitting diode compared to the rich fluorescent lamps and to reduce the cost for a long time, reducing energy consumption and to reduce ... -
Leak test method for diffusion pump: a case study of leak testing method for diffusion pump in real industry
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project is related to a real industry case involving the Quality Assurance Department for UWC Holdings Sdn. Bhd. In this project the problems and proposal of solutions were presented to solve the problems that ... -
Lean assessment in manufacturing industry
(Universiti Malaysia Perlis (UniMAP), 2016-05)Manufacturing organizations are under pressure to improve productivity and reduce costs through the realization of lean culture. This paper approaches lean culture and aims to identify and measure the closely related ... -
Line balancing at a packing process of medical products
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)The main purpose for preparing this report is to record all the progress and results obtained during the period required to complete this task. Project conducted for the two semester, semester 1 and 2 for 2009/2010 is ... -
Low cost ergonomics improvement in industry
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010)Not available -
Low cost ergonomics improvement in small & medium enterprise (SME)
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010)Ergonomics is important in our daily lives, but not many of attention on it. We cannot run from problems in the ergonomics in undergoing daily activities. We are not aware that we are sitting on a chair that is too low, ... -
Low cost ergonomics improvement in Small and Medium Enterprise (SME)
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)The objectives of this study are to identify the common ergonomics issues or problems in Small and Medium Enterprise (SME) and to implement low-cost ergonomics improvement for SME based on selected company. This study was ...