Browsing Shamsul Baharin Jamaludin, Prof. Dr. by Title
Now showing items 68-87 of 88
-
Microwave sintering of pure iron with addition of stearic acid as binder
(Trans Tech Publications, 2012)The purpose of this study is to investigate the effect of the stearic acid as binder in sintering pure iron using a microwave furnace. The study was focused in mechanical properties such as porosity, density and micro-hardness ... -
The need to intensify research efforts in the alternative to lead shot
(Trans Tech Publications, 2014)The problem of lead poisoning resulting from the use of lead shot in hunting waterbirds and shooting sports has led to the partial ban, voluntary restriction and complete ban of lead shot in some countries. The ban resulted ... -
Optimization of sintering temperature on microwave sintering of the composite iron-chromium reinforced with alumina particles
(Trans Tech Publications, 2014-01)Microwave sintering technology has become attractive and gained interest among material researchers due its capability and advantages over conventional sintering. Since two decades ago, intensive researches on microwave ... -
Oxide semiconductors for solar to chemical energy conversion: nanotechnology approach
(Institute for Ionics, 2014)The present work considers the application of oxide semiconductors in the conversion of solar energy into the chemical energy required for water purification (removal of microbial cells and toxic organic compounds from ... -
Physical properties of FG HAP-F75 fabricated by powder metallurgy
(Universiti Malaysia Perlis (UniMAP)Centre for Graduate Studies, 2010-10-16)Functional graded (FG) HAP-F75 was prepared by powder metallurgy technique. Three layers of functional graded HAP-F75 was fabricated using single punch hydraulic press. The fabrication technique consists of mixing, pressing ... -
Potential of palm oil clinker as reinforcement in aluminium matrix composites for tribological applications
(University of Malaya, 2011)This research studied the potential of palm oil clinker as reinforcement in composite based aluminium for tribological applications. Palm oil clinker particle (POCp) reinforced aluminium matrix composites at different ... -
Preliminary Microstructure and Hardness Studies of A356/Stainless Steel Composite via Gravity Die Casting Technique
(Universiti Malaysia Perlis (UniMAP), 2007-06-09)The microstructure and hardness of A356/stainless steel composite via gravity die casting technique were evaluated. Both nearly completed bonding and incomplete bonding was seen at the stainless steel wire- A356 matrix ... -
Preliminary study of hap addition to Co-Cr-Mo alloy fabricated by powder metallurgy method
(SIRIM, 2010-11-22)This preliminary study of HAP addition in Co-Cr-Mo (F-75) was carried out by powder metallurgy method. The lab work comprises the mixing of Co-Cr-Mo with different HAP (hydroxyapatite) composition which varied from 0 wt. ... -
Preparation and characterization of Co-HA powder using modified electroless method
(Trans Tech Publications, 2014)C0-HA composite produced by simple electroless deposition method was studied. From the particle size analysis by Malvern particles analyzer its shows that 19% increment in average of the particle size powder increase after ... -
Recycled Aluminium Composite Pulley
(Malaysian Invention & Design Society (MINDS), 2006-05-19)Recycle Aluminium Composite Pulley was an environmental-friendly pulley from innovative recycle aluminium composite materials. This pulley was fabricated by using recycled aluminium alloy from automotive component reinforced ... -
Response of functionality graded hydroxyapatite/F-75 in saline solution 0.9% NaCl
(Trans Tech Publications, 2013)Functionally graded hydroxyapatite (HAP) /F-75 was fabricated using powder metallurgy technique. Samples fabricated were tested inside 0.9% NaCl to check their bioactivity reaction. After immersed, samples were analyzed ... -
Sand replacement materials (SRM) in sustainable cement composites; A concise review
(Trans Tech Publications, 2013)This paper presents a short review of research works on the development of sustainable cementitious matrix composites with addition of potential mineral wastes as sand replacement materials. The study emphasizes on the ... -
Selective extraction, separation and recovery of Cu(II) in presence of Zn(II) and Ni(II) from leach liquor of waste printed circuit board using microcapsules coated with Cyanex 272
(Springer Verlag, 2012-05)The study was conducted to optimize the selective extraction and recovery of Cu(II) in the presence of Zn(II) and Ni(II) from the leach liquor of waste printed circuit boards (PCBs). The extraction experiments were carried ... -
Simultaneous extraction and separation of Cu(II), Zn(II), Fe(III) and Ni(II) by polystyrene microcapsules coated with Cyanex 272
(Elsevier B.V, 2009-02)The preparation of polystyrene microcapsules coated with Cyanex 272 (MC-Xs) have been investigated and simultaneous extraction and separation behavior of Cu(II), Zn(II), Fe(III) and Ni(II) in both batch and packed column ... -
Sintering effects on mechanical properties of Co-HA composite prepared by modified electroless deposition.
(Trans Tech Publications, 2014)Co-HA composite produced using electroless deposition without conventional sensitization and activation treatment was studied with varying sintering temperature (1100°C, 1200°C and 1250°C). The particles size, bulk density, ... -
Structural & Magnetic Characterizations of NiLiZn Nanoferrites Synthesized by Co-precipitation Method
(Chinese Society of Metals, 2011)Synthesis of Ni 0.5Li xZn (0.5-x)Fe 2O 4 nanoparticles with x=0, 0.1, 0.2, 0.3, 0.4 and 0.5 were realized via co-precipitation method. X-ray diffraction (XRD) and vibrating sample magnetometer (VSM) measurements were ... -
Studies on mechanical alloying of Copper-Tungsten Carbide composite for spot welding electrode
(Springer New York, 2009-02-27)This article presents a study on the properties and performance of copper-based composite reinforced with recycled tungsten carbide powder as spot welding electrode. The copper-tungsten carbide composite electrode was ... -
Studies on mechanical alloying of copper-tungsten carbide composite for spot welding electrode
(Springer New York, 2009-12)This article presents a study on the properties and performance of copper-based composite reinforced with recycled tungsten carbide powder as spot welding electrode. The copper-tungsten carbide composite electrode was ... -
Sustainable porous materials for gas adsorption applications; A concise review
(Trans Tech Publications, 2013)Many new sustainable porous materials were developed for gas adsorption applications. Common materials such as activated carbon, clay materials and metal organic framework (MOF) that utilized as potential porous adsorption ... -
Synthesis and characterization of pure magnesium/bio-glass composite
(Trans Tech Publications, 2013)In this study, bio-glass 45S5 powder was added to pure magnesium powder to produce the magnesium/bio-glass composite by powder metallurgy method. The composite was synthesized based on 5 wt. %, 10 wt. % and 15 wt. % of ...