• The Characterization of Bario Rice Starch-nanoHA Scaffolds using SEM and Dielectric Measurement 

  M.Riza, Roslan; Nashrul Fazli, Mohd Nasir; M.F., Abdul Khalid; Nasrul Amri, Mohd Amin; N. Mohammad; Beh Chong, You; Cheng Ee, Meng; Mohd Shukry, Abdul Majid (IOP Publishing, 2019)

  Bone tissue scaffold had been ventured for over the decades as a solution for bone failure and trauma. Starch is the most common natural polymer that has been used as a biomaterials and a good candidate for scaffold ...

• Hardened Glass Particle and Carbon Black using Resin for Potential Electromagnetic Shielding in Biomedical Electronic Equipments 

  Cheng Ee, Meng; Mohd Shukry, Abdul Majid; Shahriman, Abu Bakar; Nashrul Fazli, Mohd Nasir; Khor Shing, Fhan; You Kok, Yeow; Lee Kim, Yee; Mohd Ridzuan, Mohd Jamir (IOP Publishing, 2019)

  This study aims to investigate the electromagnetic properties of a composite of hardened glass particle and carbon using resin in determining the absorbability of the composite for electromagnetic interference (EMI). The ...

• The Optimization of the Hydroxyapatite (HA) Material Characteristics Produced from Corbiculacea (Etok) Shells 

  Mohd Riza, Roslan; Nashrul Fazli, Mohd Nasir; Mohd Farid, Abdul Khalid; Nur Farahiyah, Mohammad; Cheng Ee, Meng; Nor Nabielah Nazihah, Hashim; Beh Chong, You; Mohd Shukry, Abd. Majid; Nasrul Amri, Mohd Amin (IOP Publishing, 2019)

  Hydroxyapatite commonly used in medical field for tissue disease, bone disease, drug delivery and also for non-medical field purpose such as wastewater treatment. Due to excellent biocompatibility and bioactive properties, ...

• Effect of pineapple leaf (PALF), napier, and hemp fibres as filler on the scratch resistance of epoxy composites 

  Mohd Ridzuan, Mohd Jamir; Mohd Shukry, Abdul Majid; Azduwin, Khasri; E.H.D. Gan; Zuradzman, Mohamad Razlan‬; S., Syahrullail (Elsevier, 2019)

  This article presents the effects of pineapple leaf (PALF), napier, and hemp fibres as filler on the scratch resistance of epoxy composites. In particular, it explores the effect of these natural fillers on the horizontal ...

• Motorbike engine faults diagnosing system using neural network 

  Paulraj, Murugesa Pandiyan, Prof. Dr.; Mohd Shukry, Abdul Majid, Dr.; Sazali, Yaacob, Prof. Dr.; Zin, M.Z.M. (IEEE Conference Publications, 2008-12)

  Monitoring systems for motorbike industry requires high and efficient degree of performance. In recent years, automatic identification and diagnosis of motorbike engine faults has become a very complex and critical task. ...

• Qualification and lifetime modelling of fibreglass pipe 

  Gibson, Arthur Geoff; Mohd Shukry, Abdul Majid, Dr.; Assaleh, T. A.; Hale, Jack Michael; Fahrer, A.; Rookus, C. A P; Hekman, M. (Maney Publishing, 2011-03)

  Procedures for qualifying fibreglass pipes are discussed here in relation to industry needs. The ultimate elastic wall stress (UEWS) test appears to provide an efficient means of rating pressure pipe, and indeed vessels, ...

• Application of frame energy based DCT moments for the damage diagnosis in steel plates using FLNN 

  Paulraj, Murugesa Pandiyan, Prof. Dr.; Sazali, Yaacob, Prof. Dr.; Mohd Shukry, Abdul Majid, Dr.; Krishnan, Pranesh (IEEE Conference Publications, 2012-12)

  This paper discusses the application of frame energy based Discrete Cosine Transformation (DCT) moment features for the detection of damages in steel plates. A simple experimental model is devised to suspend the steel ...

• Steel plate damage diagnosis using probabilistic neural network 

  Paulraj, Murugesa Pandiyan, Prof. Dr.; Sazali, Yaacob, Prof. Dr.; Mohd Shukry, Abdul Majid, Dr.; Krishnan, Pranesh (IEEE Conference Publications, 2013-01)

  This paper discusses the application of frame energy based DFT spectral band features for the detection of damages in steel plates. A simple experimental model is devised to suspend the steel plates in a free-free condition. ...

• Stress analysis of adhesive bonding of urea granulator fluidization bed 

  Abu Nor, Bakyah; Mohd Afendi, Rojan, Dr.; Mohd Shukry, Abdul Majid, Dr.; Abdul Rahman, Abdullah; Shahriman, Abu Bakar, Dr. (Trans Tech Publications, 2014-06)

  Stress analysis of adhesive bonding of urea granulator fluidization bed was performed by using finite element method. The main objective of this project is to develop an alternative joining technique for urea granulator ...

• The interlaminar shear strength test of helical wound glass fibre reinforced epoxy laminates subjected to hydrothermal ageing 

  Mohd Shukry, Abdul Majid, Dr.; Mohd Afendi, Rojan, Dr.; Ruslizam, Daud, Dr.; Nasrul Amri, Mohd Amin, Dr.; Azizul, Mohamad; M. Hekman (Trans Tech Publications, 2014-06)

  This paper presents the experimental investigation of interlaminar shear strength (ILSS) tests of helical wound glass fibre reinforced epoxy (GRE) pipes subjected to hydrothermal ageing. Currently, the test is being used ...

• Strength of ductile adhesive butt joint bonded with dissimilar adherents: effect of surface roughness 

  Nurul Atikah; Mohd Afendi, Rojan, Dr.; Siti Hirmaliza; Mohd Shukry, Abdul Majid, Dr.; Nurul Amira; Mazlee, Mohd Noor, Dr. (Trans Tech Publications, 2014-06)

  The purpose of this project is to study the influence of the macroscopic state of surface roughness of the dissimilar adherent on the strength of adhesive joint. In this project, several types of sandpaper were used to ...

• Electrical properties investigation of unsaturated polyester resin with carbon black as fillers 

  R., Revati; Shuhaida, Yahud, Dr.; Mohd Shukry, Abdul Majid, Dr. (Trans Tech Publications, 2014-06)

  In this paper, conducting polymer composites were prepared by adding different percentage of carbon black (2, 4, 6 and 8)% to unsaturated polyester resin. Hence, this project focuses on two types of carbon black which is ...

• Strength of three-point-bending ductile adhesive joint with dissimilar adherent 

  Siti Nurhashima; Mohd Afendi, Rojan, Dr.; Nasrul Amri, Mohd Amin, Dr.; Mohd Shukry, Abdul Majid, Dr.; M.Taufik (Trans Tech Publications, 2014-06)

  In this study, an experimental investigation was conducted in order to determine the effect of different adhesive thickness (i.e., 0.1, 0.5, 0.7 and 1 mm) on strength of ductile adhesive joint. The study scope covers both ...

• Short-term test of ±55 filament wound GRE composite pipes under multiaxial stress ratios 

  Krishnan, Pranesh; Mohd Shukry, Abdul Majid, Dr.; Mohd Afendi, Rojan, Dr.; Haslan Fadli, Marzuki; Mohd Nor Fakhzan, Mohd Kazim (Trans Tech Publications, 2014-06)

  This paper discusses the the development of an automated pressure testing rig to perform a short term test; Ultimate Elastic Wall Stress (UEWS) for ±55˚ glass fibre reinforced epoxy (GRE) composite pipe under various stress ...

• Effect of nano-clay and their dispersion techniques on compressive properties of unsaturated polyester resin 

  Fartini, Mohd Suhut; Mohd Shukry, Abdul Majid, Dr.; Mohd Afendi, Rojan, Dr.; Ruslizam, Daud, Dr.; Azizul, Mohamad (Trans Tech Publications, 2014-06)

  This paper aims to understand the relationship between processing parameters and compressive properties of nanoclay filled polyester resin (dispersion method and wt% of nanoclay particles). Unsaturated polyester resin with ...

• Stress and thermal analysis of CubeSat structure 

  Nur Athirah, Matnawi; Mohd Afendi, Rojan, Dr.; Ku Hafizan; Nasrul Amri, Mohd Amin, Dr.; Mohd Shukry, Abdul Majid, Dr. (Trans Tech Publications, 2014-06)

  This paper presents the stress and thermal analysis on the CubeSat structure to study the survivability of the CubeSat during the launching process or operating condition at the orbit is presented. Various design of ...

• Effects of elevated temperatures on the compression strength of nanoclay filled unsaturated polyester resin 

  Fartini, Mohd Suhut; Mohd Shukry, Abdul Majid, Dr.; Mohd Afendi, Rojan, Dr.; Nasrul Amri, Mohd Amin, Dr.; Azizul, Mohamad (Trans Tech Publications, 2014-06)

  The paper describes the effects of the montmorillonite (MMT) fillers commonly known as nanoclay, on the compression properties of unsaturated polyester resins at different weight percentage of nanoclay. Modified resin ...

• 3D finite element stress analysis of butt adhesively bonded dissimilar joint: effect of bond thickness on strength 

  Izzawati, Basirom; Mohd Afendi, Rojan, Dr.; M. Afif; Siti Nurhashima; Ruslizam, Daud, Dr.; Nasrul Amri, Mohd Amin, Dr.; Mohd Shukry, Abdul Majid, Dr. (Trans Tech Publications, 2014-06)

  The butt joint is the most studied type of adhesive joints in the literature. However, the joint strength prediction of joints is still a controversial issue as it involves a lot of factors that are difficult to quantify ...

• Tensile strength of untreated napier grass fibre reinforced unsaturated polyester composites 

  Haameem, M.J.A.; Mohd Shukry, Abdul Majid, Dr.; E.A.H, Engku Ubaidillah; Mohd Afendi, Rojan, Dr.; Ruslizam, Daud, Dr.; Nasrul Amri, Mohd Amin, Dr. (Trans Tech Publications, 2014-06)

  This paper describes the experimental investigation of the tensile strength of untreated Napier grass fibre reinforced polyester composites. Napier grass fibres were extracted trough conventional water retting process and ...

• Effect of adhesive thickness on adhesively bonded T-joint 

  A. R., Abdullah; Mohd Afendi, Rojan, Dr.; Mohd Shukry, Abdul Majid, Dr. (IOP Publishing Ltd, 2013)

  The aim of this work is to analyze the effect of adhesive thickness on tensile strength of adhesively bonded stainless steel T-joint. Specimens were made from SUS 304 Stainless Steel plate and SUS 304 Stainless Steel ...

View more