Browsing School of Materials Engineering (Articles) by Title
Now showing items 33-52 of 560
-
Comparative characterization of Clinker’s microstructure at different temperature zone during cement production
(Science Publications, 2007)Temperature is an important parameter for transformation of minerals in clinker during cement productions. It influences the formation of alite from belite during calcinations and clinkering processes. The result of ... -
Comparative study of corrosion behavior of AA2014/15 Vol%Al2O3p and AA2009/20 Vol% SiCw
(Portuguese Electrochemical Society, 2008)The influence of heat treatment on the corrosion behavior of two aluminium matrix composites (AA2014/15 vol% Al2O3p - composite A and AA2009/20 vol% SiCw - composite B) was analyzed in 3.5% sodium chloride solution. The ... -
Comparative study on human and bovine AT-SC isolation methods
(Elsevier Ltd., 2013-11)Mammalian adipose tissue derived stem cells (AT-SC) have a tremendous potential in regenerative medicine for tissue engineering and somatic nuclear transfer (SNT). The isolation methods of human and bovine adipose tissue ... -
Comparative study on thermal, compressive, and wear properties of palm slag brake pad composite with other fillers
(Trans Tech Publications, 2011)The attractive performance-to-cost ratio associated with the incorporation of waste material in composite formulations used to produce brake pads has stimulated the idea of exploring the possible incorporation of additional ... -
The comparison between four PLCC packages and eight PLCC packages in personal computer (PC) using computational fluid dynamic (CFD), fluent software™ using epoxy moulding compound material (EMC)
(Trans Tech Publications, 2013)The paper present the three dimensional numerical analysis of heat and fluid flow through Plastic Leaded Chip Carrier (PLCC) packages in inline orientation horizontally mounted on a printed circuit board in a wind tunnel ... -
Comparison between single and multi gates for minimization of warpage using taguchi method in injection molding process for ABS material
(Trans Tech Publications, 2013-12)In this study, a mold is designed in single and dual type of gate in order to investigate the deflection of warpage for thick component in injection molding process. Autodesk Moldflow Insight software was used as a medium ... -
Comparison of dynamic mechanical properties of non-superheated and superheated A357 alloys
(Slovak Academy of Sciences, 2010-03-01)The influence of superheat treatment on the microstructure and dynamic mechanical properties of A357 alloys has been investigated. The study of microstructure was performed by optical microscope. Dynamic mechanical ... -
Comparison of geopolymer fly ash and ordinary Portland cement to the strength of concrete
(American Scientific Publishers, 2013-12)The aim of this study is to evaluate the effect of various fly ash: aggregate ratios by using fly ash (FA) based geopolymer compared to ordinary Portland cement (OPC) on the compressive strength of concrete. The different ... -
Comparison of liquid phase sintering and Cu-melt infiltration methods to consolidate 80W-Cu composite using nickel as sintering activator
(Trans Tech Publications, 2013)In this article, studies were conducted to evaluate the densification of W- Cu sintered compacts produced using two methods; liquid phase sintering (LPS) and combination of liquid phase sintering and liquid infiltration ... -
Comparison of original and sintered LUSI mud from East Java, Indonesia as raw material for making a geopolymer
(American Scientific Publishers, 2013-01)This paper presents the characterization of LUSI mud from East Java, Indonesia, as a potential raw material for making a geopolymer. Two types of LUSI mud were analyzed, i.e., original LUSI mud and LUSI mud that had been ... -
Comparison on biodegradation of anionic dye orange II and cationic dye methylene blue by immobilized microorganisms on spent granular activated carbon
(Taylor & Francis Online, 2014-01)Activated carbon adsorption and biological degradation are two important methods used in the treatment of industrial wastewater among others. The objective of this study is to investigate the biodegradation of anionic dye ... -
The compatibilty of TPU and NR blends
(Trans Tech Publications, 2014-01)The blends of thermoplastic polyurethane (TPU) with natural rubber (NR) at four different blends ratios were prepared via melt blending, with addition of liquid natural rubber (LNR) as compatibilizer. The effect of blend ... -
Compressive and wear resistance of alumina reinforced fe-cr matrix composites
(Scientific.Net, 2012-12)Fe-Cr matrix composite reinforced with alumina with mean powder sizes of 13, 23, 24 and 64 μm was successfully obtained through powder metallurgy method. The powder mixture were blended at a rotating speed of 250 rpm for ... -
Compressive strength and crack propagation of cement composites reinforced coconut fibre
(Medwell Journals, 2012)This study presents the compressive strength and crack propagation of cement composites reinforced coconut fibre. The development of cement composites in this research were done by substituting coconut fibre to the portion ... -
Compressive strength and morphology of fly ash based geopolymer as artificial aggregate with different curing temperature
(Trans Tech Publications, 2014)This paper presented the compressive strength of geopolymer paste with different NaOH concentration and morphology analysis for sintered artificial aggregate. This artificial aggregate was produce based on mix design with ... -
Compressive strength of fly ash based geopolymer / glass fiber composite via filament winding
(Trans Tech Publications, 2014)In general, filament winding technique is used to fabricate the composite pipes using continuous fiber and matrix resin. In this study, fly ash based geopolymer resin composites reinforced by continuous glass fiber were ... -
Copper ion-exchanged channel waveguides optimization for optical trapping
(Elsevier Ltd., 2013-08)Optical trapping of particles has become a powerful non-mechanical and non-destructive technique for precise particle positioning. The manipulation of particles in the evanescent field of a channel waveguide potentially ... -
Copper-filled electrically conductive adhesives with enhanced shear strength
(ASM International, 2014-09)In this study, the effects of diethyl carbitol (diluent) and tertiary amines on the electrical, mechanical, and rheological properties of the Cu-filled polyurethane-based electrically conductive adhesives (ECAs) were ... -
Corn cob filled chitosan biocomposite films
(Trans Tech Publications, 2013)Recently, there has been renews interest in chitosan as materials in producing of biocomposite films. The chitosan (CS)/corn cob (CC) biocomposite films were prepared by solvent casting method. The effect of CC content on ... -
Correlating composition design and properties of calcined kaolin geopolymeric powder
(American Scientific Publishers, 2013-12)This paper discussed the relation between composition design and properties of calcined kaolin geopolymeric powder. Geopolymeric powder was produced by applying the geopolymerization process. The solids-to-liquid ratios ...