School of Microelectronic Engineering (FYP): Recent submissions
Now showing items 41-60 of 153
-
Study the effect of environmental noise on Infrared TX–RX Circuit Signals
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)Infrared wireless communications systems have been massively growing in the past few years. There has been a high priority needs include systems for small group communications, portable receivers, and portable transmitters. ... -
Serial Peripheral Interface (SPI) (Front End Design)
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008)The Serial Peripheral Interface Bus or SPI bus is a synchronous serial data link. This device is one of ASIC design chip that have in the market. In this final year project the new form of device will be created from the ... -
Vertical electrostatic comb drive actuator for MEMS design
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)This report serves as a summary for project titled Vertical Electrostatic Comb-Drive Actuator. A comb-finger structure is disclosed for use in optical switching applications. Large displacements of movable fingers were ... -
MEMS Cantilever beam monitor
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)Three cantilever beam monitor has been designed using the same material and dimension. They are the center, left and right cantilever beam with their own contact pad. The center beam can be displaced to the right or left ... -
Analysis the role of supply voltage and load capacitor in small-signal MOSFET amplifiers
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-03)The main objective of this project is to investigate the role of supply voltage and load capacitance in the performance of small-signal MOS amplifier with the PSpice simulation for the Common Source, Common Gate and Common ... -
Study of Deposition Time Influence the Conical Structure during Electron Beam Induced Deposition (EBID)
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)Atomic force microscopy (AFM) is now a well-established technique for the surface characterization and imaging of a variety of materials. In AFM the accuracy of data is often limited by the tip geometry and the effect on ... -
Car Reverse Sensor with distance display
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-03)Car reverse sensor with distance display is a design to improve driver awareness in maneuvering reversed gear. The design also helps deaf person to benefit from today technology. The distance displays fast enough to give ... -
Vertical-Lateral Thermal Actuator for MEMS design
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)Compact vertical and lateral thermal actuator has been design and simulation. The process of the simulation is to apply the current so it can make the arms hot enough to bend the design towards the cold arms. This current ... -
Study and improvement of UniMAP Air Shower Room
(Universiti Malaysia Perlis, 2008-04)This Air Shower Room is a project that will be used to control air quality especially to all industry and all semiconductor factory. The air blower which is play a main function will absorb the dust and dirt from the ... -
PIC based smart lamp control and monitoring unit in airport
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)This project representing one product or the rule that easier in the implementation of the switching system that was met in any big buildings like the airport. This is built with made a microcontroller model PIC16F877A ... -
Design prototype of prepaid water dispenser
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)Telecommunication technology have change currently, had many change the pattern human life.This is because telecommunication technology already contribute a lot to pattern of life a more convenient. Realizes of this ... -
Theoretical study, simulation & fabrication of Dry Oxidation in terms of SiO2 layer thickness, resistivity & surface roughness
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)Oxidation is a process used in wafer fabrication. The goal of oxidation is to grow a high quality oxide layer on a silicon substrate. During oxidation a chemical reaction between the oxidants and the silicon atoms produces ... -
Study of the thickness of the Silicon Dioxide on wafer using Dry and Wet Oxidation method
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-03)Studies of the interaction of O2 and O with Si(100) at a fundamental level are reviewed. Both atomic and molecular chemisorbed species have been found on these surfaces. STM studies have given a great deal of information ... -
Study of the effect of different Gases parameter in Dry Etching process on Etch Rate profile
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)The principal focus of this project is dry etching technique by using the Inductively Couple Plasma-Reactive Ion Etching (ICP-RIE). An (ICP) system was chosen because of its high plasma density and low cost relative to ... -
Study of aspect ratio performance on Silicon Oxide wet etching by using Profilometer, AFM and SEM
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-03)A study of aspect ratio performance on silicon oxide is developing to predict the oxide profile on surface of wafer. The main focus of this project is to perform and produce a high profile of silicon oxide under profiler ... -
Temperature and energy dependence of diffusion in Solid - Effect of Diffusion Coefficient and Junction Depth
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)This project entitled Effect of Diffusion Coefficient and Junction Depth on Variation of Temperature and Energy is carry out to find the effect of the junction depth and the diffusion coefficient and how temperature and ... -
Study of the temperature effect on thickness and surface roughness of SiO2
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)Oxidation is one of the most important thermal processes in semiconductor fabrication. The profile of oxide layer is varied to its different applications. Many factors can affect the profile of the SiO2 layer. In this ... -
Single Crystal SiC Capacitive pressure sensor design and analysis using MEMS Pro L-Edit and Samcef Field & Oofelie software
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-03)Single crystal 3C-SiC capacitive pressure sensors are proposed for high-temperature sensing applications. SiC is an attractive material for harsh environment micromachined transducers due to its outstanding electrical, ... -
Ultrasonic Range Meter using PIC19F876
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)This thesis reports the design and implement of a relatively inexpensive, but versatile and experimental of range meter controlled suitable for use in either a research or educational setting. The project is nearing ... -
Fabrication and simulation of PNP Bipolar transistor based on Spin On Dopant technique and Electrical characterization
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)In this project, the fabrication and simulation of pnp transistor was performed. From fabrication process, the electrical characteristic and sheet resistance of the device was observed by 4 point probe measurement. The ...