Browsing School of Microelectronic Engineering (FYP) by Subject "Microelectronics"

Now showing items 1-12 of 12

    • Analysis of square shaped Microstructure based Electron Beam induced deposition 

      Siti Fatimah Abd. Rahman (Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)
      The fabrication of square shaped microstructures is studied by electron beam induced deposition (EBID) method using Scanning Electron Microscopy (SEM). EBID is a technique that allows the resistless deposition directly ...

    • Design and simulation of Piezoresistive pressure sensor 

      Mohd Hilmi Mohd Nor (Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-03)
      The piezoresistive effect describes the changing electrical resistance of a material due to applied mechanical stress. Electrical resistor will change its resistance when it experiences a strain and deformation. Pressure ...

    • Design and simulation of Piezoresistive tactile sensor 

      Nahmar Harun (Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)
      Piezoresistive tactile sensor is use to measure contact force and to characterize surface roughtness of the object. The main application of piezoresistive tactile sensor is in robotic dexterous manipulations tasks. This ...

    • The influence of the accelerating voltages on the growth of the square structure during Electron Beam Induced Deposition (EBID) method 

      Muhammad Afiq Abdul Aziz (Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)
      Electron beam induced deposition (EBID) is a method for high-resolution direct material deposition from the gas phase in the Scanning Electron Microscopy (SEM) onto a substrate. In this project, EBID method has been used ...

    • Mems Microrelay: Design, Modeling, and Simulation 

      Yap David (Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2007-05)
      A newly design of single pole single throw piezoelectric vertical actuation MEMS microrelay was successfully designed and modeled at the end of this project. This was implemented by using MEMS Pro LEdit CAD Modeler. Then, ...

    • Microfluidic Poly-Si Electrodes Capacitor ( Fabrication & Testing ) 

      Esmal Fhadly, Abd Malek (Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2007-03)
      In this project, I have to design, fabricate and testing a Microfluidic capacitor. The dielectric insulator is replaced with a dielectric fluid (deionized water) instead of usual solid state materials. The conductive ...

    • Study of acceleratin voltage influence the Conical structure during Electron Beam Induced Deposition (EBID) 

      Muhammad Afif Abdul Rahman (Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-03)
      Electron beam induced deposition (EBID) is a well established technique for highresolution direct material deposition from the gas phase onto a substrate. A finely focused electron beam of a scanning electron microscope ...

    • Study of Deposition Time Influence the Conical Structure during Electron Beam Induced Deposition (EBID) 

      Mohamad Sharizal Md Ilias (Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)
      Atomic force microscopy (AFM) is now a well-established technique for the surface characterization and imaging of a variety of materials. In AFM the accuracy of data is often limited by the tip geometry and the effect on ...

    • Theoretical study, simulation & fabrication of Dry Oxidation in terms of SiO2 layer thickness, resistivity & surface roughness 

      Mohd Adam Alias (Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)
      Oxidation is a process used in wafer fabrication. The goal of oxidation is to grow a high quality oxide layer on a silicon substrate. During oxidation a chemical reaction between the oxidants and the silicon atoms produces ...

    • Ultrasonic Range Meter using PIC19F876 

      Muhammad Shukran, Ghanim (Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)
      This thesis reports the design and implement of a relatively inexpensive, but versatile and experimental of range meter controlled suitable for use in either a research or educational setting. The project is nearing ...

    • Vertical electrostatic comb drive actuator for MEMS design 

      Wan Mokhdzani Wan Nor Haimi (Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)
      This report serves as a summary for project titled Vertical Electrostatic Comb-Drive Actuator. A comb-finger structure is disclosed for use in optical switching applications. Large displacements of movable fingers were ...

    • Vertical-Lateral Thermal Actuator for MEMS design 

      Muhammad Arefendy Ab. Rahim (Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)
      Compact vertical and lateral thermal actuator has been design and simulation. The process of the simulation is to apply the current so it can make the arms hot enough to bend the design towards the cold arms. This current ...