Browsing School of Manufacturing Engineering (FYP) by Title
Now showing items 285-304 of 336
-
A study of compressive and impact properties of Jute laminate structure composite
(Universiti Malaysia Perlis (UniMAP), 2016-06)This research was performed in the form of experimental study about sandwich panel composite structure. The sandwich specimen was prepared in configuration of Jute/Epoxy/Honeycomb Nomex, Jute/Epoxy/Polyvinyl Chloride ... -
Study of controlling system for high speed mud boat
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project focuses to study the control system for high speed mud boat. This study intends to identify the best type of control system for use on high-speed mud boat. A several studies have been done on the system ... -
Study of heat transfer characteristics of Al2O3 nanoparticles in heat pipes
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project deals with the study of heat transfer characteristics of aluminium oxide nanoparticles in heat pipe. A heat pipe is a simple heat transfer device that can transfer large amount of heat from the evaporator ... -
Study of heat transfer characteristics of Sio2 nanoparticles in heat pipes
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project deal with study of heat transfer characteristics of silicon oxide, SiO2 in heat pipe. To achieve better performance of heat pipe, increasing its efficiency is a challenge nowadays. Effects of implementation ... -
Study of influence Plasma Arc cutting with response surface method
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2008-04)The properties of plasma generated for the air plasma cutting process have been investigated in this study. The plasma arc cutting process employs a plasma torch with a very narrow bore to produce a transferred arc to the ... -
A study of low cost ergonomic improvements in small and medium enterprise (SME)
(Universiti Malaysia PerlisSchool of Manufacturing Engineering, 2009-05)The research is about to see the ergonomic concept application in all working field that was manually performed by the employee at Small and Medium Enterprise (SME) as in the Sayyidah Roti Arab factory. A Nordic questionnaire ... -
Study of machining parameter of wire electrical discharge of nickel-base alloys using response surface method
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)Study of Machining Parameter of Wire Electrical Discharge of Nickel-Base Alloys using Response Surface Method (RSM) had been done in this project. WEDM machine that use for this project is SODICK AQ327L that located at ... -
A Study of Single Minute Exchange of Die Methodology Improvement Using Design-Based Elements
(Universiti Malaysia Perlis (UniMAP), 2016)Single Minute Exchange of Dies (SMED) is a lean tool designed to reduce changeover time and improve manufacturing flexibility. Current methodology is too focused on the use of organizational improvements, such as parallel ... -
Study of surface roughness during droplet impact on a heated aluminum surface
(Universiti Malaysia Perlis (UniMAP), 2016-06)Study of surface roughness during droplet impact on a heated aluminium is to look into the effect of droplet impact on surface roughness after the droplet impinged on the hot surface. The primary problem with this task ... -
Study of surface roughness during droplet impact on a heated stainless steel surface
(Universiti Malaysia Perlis (UniMAP), 2016-06)This is a study of surface roughness during impact of water droplet impinging on a heated stainless steel surface. In this study, the effect of the droplet impingement on the surface were presented. The topic about the ... -
A study of thin shell plastic part quality in the plastic injection molding
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)As the part’s dimensions become smaller, its thickness becomes smaller. In plastic injection molding, the production of the thin walled parts is very difficult. It’s hard, because melted plastic cannot easily fill the ... -
A study of thin shell plastic part quality in the plastic injection molding
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010)As the part’s dimensions become smaller, its thickness becomes smaller. In plastic injection molding, the production of the thin walled parts is very difficult. It’s hard, because melted plastic cannot easily fill the ... -
The study of value stream mapping (VSM) and Kanban in an automotive parts manufacturer
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)This research addresses the application of lean manufacturing concepts to the continuous process sector with a focus on the production manufacturing plant. The goal of this project is to make an improvement by applying ... -
A study of warpage and weld line defects on a plastic composite’s manhole cover
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)Manhole covers are generally made out of cast iron in order to bear the large loads [1]. This study is about choosing and identifying the most suitable plastic composites material which can best replaced cast iron The ... -
A study of warpage and weld line in a composite motorcyle engine oil cover using mold flow analysis software
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010)Today’s emphasis is placed on lowering production cost and weight. By replacing the metal with plastic composites, it is said to be achieved the goals compared with aluminum equivalent. Motorcycle engine oil cover is a ... -
A study of warpage and weld line in a composite motorcyle engine oil cover using mold flow analysis software
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2014)Today’s emphasis is placed on lowering production cost and weight. By replacing the metal with plastic composites, it is said to be achieved the goals compared with aluminum equivalent. Motorcycle engine oil cover is a ... -
The study of yamazumi board in an automotive parts manufacturer
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010) -
A study on contraction of Pneumatic Artificial Muscle (PAM) for load-lifting
(Universiti Malaysia Perlis (UniMAP), 2016-06)Pneumatic Artificial Muscle (PAM) is a type of actuator that similar to human muscle. The PAM is used for converting pneumatic power to pulling force and eventually causing movements of the mechanism. One of the potential ... -
A study on design and develop a concurrent problem solving method in mould flow analysis
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2009-05)CAE techniques have in recent years, become increasingly popular in plastic injection molding. However, in most practices, either molding parameters are not optimized or the optimization techniques are too complex to use. ... -
A study on different localities of Soft Exoskeleton for hand grasping using pneumatic actuator
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project is related to the soft exoskeleton for hand grasping using pneumatic actuator on different localities. The device is lightweight and easy wearable due to the usage of soft pneumatic actuator. The number of ...