Final Year Project Papers & Reports: Recent submissions
Now showing items 881-900 of 2200
-
Design and development of automatic battery electrolyte level maintenance system
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05) -
Changeover time reduction for die cut machine
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010)A rapid changeover capability is widely acknowledged as an essential prerequisite to flexible, responsive small batch manufacturing. Its importance in mass customization is recognized, where minimal losses need to be ... -
Experimental Analysis of the efficiency of tungsten inert gas (TIG) machining for different materials
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)This paper presents an experimental study of efficiency of Tungsten Inert Gas (TIG) with various parameters in different materials. The experiments will base on Design of Experiment with the Taguchi Method. Experiments ... -
Study on quality of wastewater from car wash premises
(Universiti Malaysia Perlis (UniMAP)School of Environmental Engineering, 2011-04)Car wash wastewater (CWW) normally contains oil and grease, rubber, paints, phosphate, dust and sand and organic matter. The wastewater runoff from the car enters the gutters gone into the storm water system. The wastewater ... -
Natural vaporization system of seawater using plastic plate
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)This report discussed about natural vaporization system of seawater using plastic plate. This experiment is based on the idea that every kind of water can be turn into water droplet using the concept of vaporization. ... -
Design and development of semi-auto universal coconut machine (Coconut Extracting Machine)
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)In process to develop Small and Medium Industry sector (SMI), various creations and machine were created. Coconut Extracting Machine was devised indirectly develops this sector. The combination of grating and extracting ... -
Effect of sintering parameter on the densification and mechanical properties of microwave sintered copper
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010)This project is conducted to analyze Effect of sintering parameter on the densification and mechanical properties of microwave sintered copper. This project used design of experiment to design experiment run, analyze the ... -
Investigations of a part jamming probability into a chute of transport system
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)The main purpose for preparing this report is to record all the progress and results obtained during the period specified to complete this task. Projects handled for both semesters, semesters 1 and 2 2009/2010 are to ... -
A study of warpage and weld line in a composite motorcyle engine oil cover using mold flow analysis software
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010)Today’s emphasis is placed on lowering production cost and weight. By replacing the metal with plastic composites, it is said to be achieved the goals compared with aluminum equivalent. Motorcycle engine oil cover is a ... -
A manufacturing shop floor problem
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-03)Quality Control (QC) are scientific management tools, which are uncomplicated used and easy to understand. It forms the fundamental foundation for all problem solving and quality control activities. The most important of ... -
A study of thin shell plastic part quality in the plastic injection molding
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)As the part’s dimensions become smaller, its thickness becomes smaller. In plastic injection molding, the production of the thin walled parts is very difficult. It’s hard, because melted plastic cannot easily fill the ... -
Design and development of fish food machine
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)The objectives of this project are to design, develop and to improve the fish food machine and to understand and apply CAD software as a tool in engineering design. Engineering method that have been applied in this project ... -
Optimization of continuous casting process in steel manufacturing industry
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)The continuous casting process is used for solidifying molten steel into semifinished steel. The technology for Secondary Cooling Zone (SCZ) is extremely important for output of casting machine and billet quality. ... -
Design and development of a ping pong training device
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)The purpose and goal of this final year project is to show the design of ping pong server machine is effective in ping pong training section. In addition, the use of ping pong server machine can helps to improve ping pong ... -
Design and development of vinegar plant layout and output capacities study
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)A design and development of vinegar plant layout and output capacities study is project to solving problem in Malaysia that no any vinegar plant of local fruit to meet the market demand and promoting our local fruits ... -
A study on surface roughness of wood using CNC milling process
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)The important aspect in machining process is the quality of milled product surface. Therefore, the choice of current cutting parameter is very important in order to obtain the desired surface finish. Thus, measuring and ... -
Tunneling machining characteristics of Aluminum matrix composite using a wire electrode discharge machining (WEDM)
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)This thesis presents the machining of Aluminium Matrix Composites( AMCs) using wire electro-discharge machining (WEDM) with brass wire diameter of 0.25mm used as the tool electrode. The main purpose of this study was to ... -
Investigation on radial curve vane air swirler to determine the effect on combustion in the combustion chamber that uses butane gas fuel
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-04)The research is about investigation on radial curve vane air swirler to determine the effect on combustion in the combustion chamber that uses butane gas fuel. Air swirlers with vane angle of 20º and 60º is use to make ... -
Design and development of shake-charged torchlight
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010)A prototype of Shake-Charged Torchlight has been designed and developed in this Final Year Project. Shake-Charged Torchlight is an additional mechanism which allows to be self-charged by shaking movement. This torchlight ... -
Design and development of a soap pilot plant and output capacity study
(Universiti Malaysia Perlis (UniMAP)School of Manufacturing Engineering, 2010-05)A design and development of Soap Pilot Plant and output capacity study is project to study the production flow of soap manufacturing, design plant layout of soap pilot plant and study capacity of soap per day. In producing ...