Final Year Project Papers & Reports: Recent submissions
Now showing items 241-260 of 2200
-
Mechanical properties of Aluminium (experiment and finite element analysis)
(Universiti Malaysia Perlis (UniMAP), 2016-06)Aluminium are the material that can be failure when the force applied with plastic deformation. Mechanical properties of a material describe how it will be reacting to physical forces. Tensile test is commonly used to ... -
Preliminary design and development of dry wear tester - pin on disc jigs
(Universiti Malaysia Perlis (UniMAP), 2016-05)Polishing and Grinding process are the important process in the Powder Metallurgy. The purposes of this test are to study about the wear rate, mass of material removal rate and the character of the material that used. ... -
Investigation of dimensional accuracy and chip formation on through hole drilling of mild steel
(Universiti Malaysia Perlis (UniMAP), 2016-05)Drilling process is among the last proses in manufacturing were highly focused in the industry due to huge impact on the final product. Therefore, a method for determining appropriate drilling techniques and parameters ... -
Mechanical properties of ductile materials (experiment and finite element analysis)
(Universiti Malaysia Perlis (UniMAP), 2016-06)Tensile test is one of the ways to study how strong a material. By leaving the damaged procedure, tensile test tend to be more accurate to compare it to other similar hardness test. The most of important in mechanical ... -
Design and development of a rack and pinion steering system for F1 cart
(Universiti Malaysia Perlis (UniMAP), 2016)This is study of rack and pinion steering system that replace the existing direct linkage steering system on SMaRT (School of Manufacturing Racing Team) F1 cart. This reports includes the study of the potential for ... -
Characterizing the kinetic of browning index, total chlorophyll and total phenolic content of clinacanthus nutans extract
(Universiti Malaysia Perlis (UniMAP), 2016-06)Clinacanthus nutans is well known for a long time for being used as traditional medicine in Malaysia to treat skin rashes, venomous insect bite and fever. Due to the benefits of this plant, a few manufacturer starts to ... -
Feasibility study and design of natural dehumidification method using desiccant for model house
(Universiti Malaysia Perlis (UniMAP), 2015-12)This case or research is feasibility study and design of natural dehumidification method using desiccant for model house. Desiccant dehumidification is function to improvise the nowadays heating, ventilation and air ... -
Design and fabrication of an explosive compaction apparatus
(Universiti Malaysia Perlis (UniMAP), 2016-05)Explosive compaction is the dynamic processes that offer the prospect of producing the high temperatures necessary for decent local metallurgical bonding at the powder particle interfaces. The stronger the press, the ... -
On study on heat flux variation due to temperature, humidity and ventilation flow of a model house for a certain continuous period
(Universiti Malaysia Perlis (UniMAP), 2016-05)The aim of this study was to understand and establish passive cooling method in hot humid climates. This is because Malaysia received high temperature with low air velocity that can influence the thermal comfort. The review ... -
Analysis of strength on the thick plate part using response surface methodology
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project is about research on the analysis of strength on the thick plate part (thickness of the part is more than 3mm) using Response Surface Methodology (RSM). The objective of this project is to improve the ... -
Thick plate part using genetic algorithm methodology
(Universiti Malaysia Perlis (UniMAP), 2016-06)This study focuses on the optimisation of the injection moulding parameters to maximise the strength on the moulded parts produced using Autodesk Moldflow Insight (AMI) 2012. The strength of the moulded parts moulded ... -
Study of heat transfer characteristics of Al2O3 nanoparticles in heat pipes
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project deals with the study of heat transfer characteristics of aluminium oxide nanoparticles in heat pipe. A heat pipe is a simple heat transfer device that can transfer large amount of heat from the evaporator ... -
Study of surface roughness during droplet impact on a heated aluminum surface
(Universiti Malaysia Perlis (UniMAP), 2016-06)Study of surface roughness during droplet impact on a heated aluminium is to look into the effect of droplet impact on surface roughness after the droplet impinged on the hot surface. The primary problem with this task ... -
Analysis of shrinkage on thick plate part using genetic algorithm
(Universiti Malaysia Perlis (UniMAP), 2016-05)Injection moulding process has been widely used to produce plastic products with various shapes for high productivity and high volume products with low cost. However there are several defect which can influence the quality ... -
Axial and lateral compression behaviour of Flax fibre reinforced epoxy composites with winding at different angle
(Universiti Malaysia Perlis (UniMAP), 2016-06)Nowadays composites made of fibres are used in many types of industries. But there are problem with poor transmission load and low strength of specimen composite tube. This study investigates the effect of filament winding ... -
Product design and development using Design For Assembly (DFA) method: a case study on automated swallow feeding machine
(Universiti Malaysia Perlis (UniMAP), 2016-06)This final year report is focuses on producing design concept of the swallow feeding machine and a case study for easy assembly for automated swallow feeding machine. In order to attract the swallows into the building, ... -
Design and fabrication of portable cleaning machine for raw edible bird’s nest
(Universiti Malaysia Perlis (UniMAP), 2016-06)Edible bird’s nest is one of the demanding food products. Removing the impurities in raw edible bird’s nest is generally known as the most complicated cleaning process especially for Grade C raw edible bird’s nest. ... -
Design and fabricate a mini tensile testing machine
(Universiti Malaysia Perlis (UniMAP), 2016-05)This project is to design and fabricate a small size and portable of tensile test machine that can be used for laboratory teaching purpose. Existing tensile testing machine in laboratory is not enough to accommodate ... -
Design and development of the vibrating sifter system for the existing design of dried chilli seed Separating Machine
(Universiti Malaysia Perlis (UniMAP), 2016-06)Design and development of the vibrating sifter system for the existing design of dried chilli seed separating machine based on the problem existing which to design the adjustable vibrating system of the sifter and the ... -
Preliminary design and development of grain dryer fired by microwave
(Universiti Malaysia Perlis (UniMAP), 2016-06)This project aimed is to determine the potential of obtaining dryer grain in a microwave energy. Grain drying is one of the most energy consuming processes on farms. It has also a lot of potential for energy savings. ...