Browsing by Author "Zuhailawati, Hussain"

Now showing items 1-9 of 9

    • Compressive and wear resistance of alumina reinforced fe-cr matrix composites 

      Saidatulakmar, Shamsuddin; Shamsul Baharin, Jamaludin, Prof. Dr.; Zuhailawati, Hussain; Zainal Arifin, Ahmad (Scientific.Net, 2012-12)
      Fe-Cr matrix composite reinforced with alumina with mean powder sizes of 13, 23, 24 and 64 μm was successfully obtained through powder metallurgy method. The powder mixture were blended at a rotating speed of 250 rpm for ...

    • Dry sliding wear and compressive strength of Fe-Cr matrix composite with and without Al2O3 reinforcement 

      Shamsul, Baharin Jamaludin, Prof. Dr.; Saidatulakmar, Shamsuddin; Zuhailawati, Hussain; Zainal Arifin, Ahmad (IEEE Conference Publications, 2011)
      Fe-Cr matrix composites reinforced with Al2O3 particulates fabricated by powder metallurgy (PM) method offer potential for cheaper wear resistance materials and high temperature application. The influence of Al2O3 amount ...

    • The effects of Al2O3 amount on the microstructure and properties of Fe-Cr matrix composites 

      Saidatulakmar, Shamsuddin; Shamsul Baharin, Jamaludin, Prof. Dr.; Zuhailawati, Hussain; Zainal Ariffin, Ahmad (Springer, 2010-12)
      Iron based matrix composites reinforced with 5 to 25 wt pct of Al2O3 particles were fabricated using the powder metallurgy method. The samples were prepared by mixing at 250 rpm for 30 minutes, uniaxially pressing at 750 ...

    • Fabrication of titanium carbide reinforced copper matrix composite by in-situ processing 

      Nur Hawadah, Mohd Subhi; Zuhailawati, Hussain; Radzali, Othman (Universiti Malaysia PerlisSchool of Materials Engineering & School of Environmental Engineering, 2010-06-09)
      Composite materials with copper matrix and ceramic particle reinforcements provide an alternative material for scope for producing relatively high thermal conductivity, electrical conductivity and hardness properties. Most ...

    • Formation of TiC-reinforced iron based composite through carbothermal reduction of hematite and anatase 

      Mohd Salihin, Hassin; Zuhailawati, Hussain; Samayamutthirian, Palaniandy (Universiti Malaysia PerlisSchool of Materials Engineering & School of Environmental Engineering, 2010-06-09)
      In this research carbothermal reduction of mechanical activated hematite (Fe2O3), anatase (TiO2) and graphite (C) was investigated. The mixtures of raw materials with composition of Fe-20vol%TiC were mechanically activated ...

    • Heating rate effects on properties of powder metallurgy Fe-Cr-Al2O3 composites 

      Saidatulakmar, Shamsuddin; Shamsul Baharin, Jamaludin, Prof. Dr.; Zuhailawati, Hussain; Zainal Arifin, Ahmad (Universiti Malaysia PerlisSchool of Materials Engineering & School of Environmental Engineering, 2010-06-09)
      The aim of this study is to determine the optimum heating rate in fabricating Fe-Cr-Al2O3 composites by powder metallurgy methods. The Fe-based composites reinforced with ceramics are widely used due to their high strength, ...

    • Mechanical properties of Alumina - Ysz composite and 6061 Al Alloy joints fabricated by friction welding method 

      Uday, M. B.; Ahmad Fauzi, Mohd Noor; Zuhailawati, Hussain; Ahmad Badri, Ismail (Universiti Malaysia Perlis, 2009-12-01)
      Friction welding method is one of the most simple, economical and highly productive methods in joining similar and dissimilar metals. It is widely used in the automotive, aircraft and aerospace industrial applications. For ...

    • Microstructure investigations of in-situ copper tungsten carbide composite by mechanical alloying 

      Mahani, Yusoff; Zuhailawati, Hussain; Radzali, Othman (Universiti Malaysia PerlisSchool of Materials Engineering & School of Environmental Engineering, 2010-06-09)
      An in-situ composite of copper and tungsten carbide powder was prepared by mechanical alloying of elemental powder. The sample has been milled in a high-energy ball mill for 20 h at different milling speed i.e. 100, 200, ...

    • A review on Alumina based ceramic composites as cutting and machining tool materials 

      Mary, Donnabelle Balela; V., Vannaladsaysy; Zuhailawati, Hussain (Universiti Malaysia Perlis, 2007)
      New trends in the cutting and machining tool industry include faster cutting rate, dty cutting and highly wear resistant tool materials. These requirements are necessary for higher production rate and improved dimensional ...