This page provides access to research works by Faizul Che Pa, currently a Senior Lecturer of School of Material Engineering, Universiti Malaysia Perlis.

News

Skills and Expertise:Material Characterization,Materials,Materials Processing,Metals,Heat Treatment,Materials Engineering,Minerals,Concrete Durability,Higher Education,Cement,Alloys,Mineral Processing,Metallurgy,Mining Engineering,Hydrometallurgy,Extractive Metallurgy

Recent Submissions

  • Alteration of solution treatment condition to the precipitation behaviour A319 alloy 

    Murizam, Darus; Shamsul, Baharin Jamaludin, Prof. Dr.; Mohd Arif Anuar, Mohd Salleh; Faizul, Che Pa; Ruhiyuddin, Mohd Zaki (Trans Tech Publications, 2013)
    The development of precipitate during ageing treatment of A319 alloy contributed significantly to the alloy strengthening mechanism. Two solution treatment temperatures which were set at 510°C and 525°C were subjected onto ...
  • Effect of pyrolysis temperature on the synthesis of carbon fiber from natural organic waste 

    Shahrizam, Saad; Faizul, Che Pa; Mohd Mustafa Al-Bakri, Abdullah; Ruhiyuddin, Mohd Zaki; Murizam, Darus (Trans Tech Publications, 2014)
    Carbon fibers are produced from natural sources of water hyacinth plants that have been dried, ground and sieved to three different particle sizes of 600 μm, 300 μm and less than 300 μm. Through the analysis of data obtained ...
  • Production of silicon carbide via grinding and heat treatment process 

    Noorina Hidayu, Jamil; Xian, W. Hui; Wan Mohd Arif, Wan Ibrahim; Faizul, Che Pa; Ruhiyuddin, Mohd Zaki (Trans Tech Publications, 2014)
    This study is to determine the properties and characterization of silicon carbide via grinding and heat treatment process. In this study, the raw materials used were waste glass and graphite powder. Silicon carbide was ...
  • Extraction of silica from palm ash using organic acid leaching treatment 

    Faizul, Che Pa; Abdullah, Chik, Prof. Madya Dr.; Md Fazlul, Bari, Dr.; Noorina Hidayu, Jamil (Trans Tech Publications, 2014)
    Agricultural wastes such as palm ash and rice husk have a possibility to be used as a usefully renewable source for production of energy and silica (SiO2). Extensive researches have been carried out to extract silica from ...
  • Extraction of silica from palm ashvia citric acid leaching treatment 

    Faizul, Che Pa; Abdullah, Chik, Prof. Madya Dr.; Md Fazlul, Bari, Dr. (AENSI Publisher All rights reserved, 2013-10)
    Agricultural wastes such as palm ash and rice husk have a possibility to be used as a usefully renewable source for production of energy and silica (SiO2). Extensive researches have been carried out to extract silica from ...
  • Extraction of silica from palm ash using citric acid leaching treatment: Preliminary result 

    Faizul, Che Pa; Abdullah, Chik, Prof. Madya Dr.; Md Fazlul, Bari, Dr. (Trans Tech Publications, 2013)
    Large quantities of agricultural wastes such as palm ash and rice husk are found throughout Malaysia, have a possibility to be used as a usefully renewable source for production of energy and silica (SiO2). Extensive ...
  • Potential application of palm ash as a raw materials in production of green glass 

    Noorina Hidayu, Jamil; Mohd Mustafa Al Bakri, Abdullah; Faizul, Che Pa; Ruhiyuddin, Mohd Zaki; Murizam, Darus; Che Mohd Ruzaidi, Ghazali, Prof. Madya; Mohamed Faisol, Mohamed Nor (Scientific.Net/Trans Tech Publications, 2012-12)
    Oil Palm Ash is one of the abundance agricultural wastes found in Malaysia. This wastes need to be disposed properly. Oil palm ash contains compounds needed to produce glass. Most of raw materials (especially silica) used ...
  • Review of extraction of silica from agricultural wastes using acid leaching treatment 

    Faizul, Che Pa; Md Fazlul, Bari; Abdullah, C. (Trans Tech Publications, Switzerland, 2012-12)
    Large quantities of agricultural wastes such as palm ash and rice husk are found in Malaysia, have a large possibility to be employed as usefully renewable to produce energy and silica (SiO2). Extensive researches have ...
  • Potential application of palm ash as raw materials to produced green glass 

    Faizul, Che Pa; Noorina Hidayu, Jamil; Ruhiyuddin, Mohd Zaki; Murizam, Darus; S. Shahrizam; Che Mohd Ruzaidi, Ghazali, Prof. Madya; Mohamed Faisol, Mohamed Nor (Universiti Malaysia Perlis (UniMAP), 2012-06-18)
    Oil Palm Ash is one of the abundance agricultural wastes found in Malaysia. This wastes need to be disposed properly. Oil palm ash contains compounds needed to produce glass. Most of raw materials (especially silica) used ...
  • Study on milling periods on the iron mill scale particle size and properties 

    Ruhiyuddin, Mohd Zaki; Faizul, Che Pa; Murizam, Darus; A. R. M., Nazri (Trans Tech Publications, 2013)
    The relations between the milling periods with the iron mill scale particle size have been studied. Iron mill scale has been chosen for this research due to the nature of itself, as a by-product. From this research, the ...
  • Properties of zinc alloy in green sand casting 

    Zatil Alyani, Mohd Amin; Faizul, Che Pa; Mohd Ichwan, Nasution, Prof. Madya Ir. (Universiti Malaysia Perlis (UniMAP)Centre for Graduate Studies, 2010-10-16)
    Zinc alloy casting industry using green sand molding is increasingly becoming to very competitive circumstance. So, this paper is to produce tertiary alloy of Zinc-Aluminium- Magnesium (Zn-3Al-2Mg) with different composition ...
  • Investigate the liberation of copper from waste Printed Circuit Boards (PCBs) 

    Mohd Zaheruddin, Kasmuin; Aimi Noorliyana, H.; Md. Fazlul, Bari; Sri Asliza, Md. Amin; Faizul, Che Pa; Kamarudin, Hussin, Brig. Jen. Dato' Prof. Dr. (Universiti Malaysia PerlisSchool of Materials Engineering & School of Environmental Engineering, 2010-06-09)
    Nowadays the waste PCBs increasing sharply proportionally the number of personal computers which is 5.7 million in 2005 and the predict amounts, it will be increase to 11.5 Million in 2010 (Unit Perancangan Ekonomi, ...
  • Morphology study on different composition of bentonite and silica sand in green sand mould for zinc alloy 

    Zatil Alyani, Mohd Amin; Faizul, Che Pa; Mohd Ichwan, Nasution, Prof. Madya Ir. (Universiti Malaysia PerlisSchool of Materials Engineering & School of Environmental Engineering, 2010-06-09)
    Zn alloy casting industry using green sand molding is increasingly becoming to very competitive circumstance, due to the various casting methods such as die cast, sand mould and so on with the recent coming of the ...
  • Properties of Zinc alloy cast product with different composition of Silica Sand and Bentonite in Green Sand Mould 

    Zatil Alyani, Mohd Amin; Faizul, Che Pa; Mohd Ichwan, Nasution, P.M Ir. (Universiti Malaysia Perlis, 2009-12-01)
    This project is to produce tertiary alloy of Zinc-Aluminium-Magnesium (Zn-3Al-2Mg) with different composition of bentonite and silica sand in the green sand mould. Zn alloy casting industry using green sand molding is ...
  • Effects of magnesium sulfate attack on ordinary portland cement (OPC) mortars 

    Mohammed Misbahul, Amin; Shamsul Baharin, Jamaludin; Faizul, Che Pa; K.K. Chuen (Portuguese Electrochemical Society, 2008)
    The chemical and mineralogical compositions in Ordinary Portland Cement (OPC) were determined and cement which is low of C3A is more easily exposed to sulfate environment. The relation between physical strength of mortars ...
  • Role of clay (Bentonite) on mold making process in foundry metallurgy 

    Mohd Ichwan, Nasution; Mohd Nasir, Zainal Arif; Che Mohd Ruzaidi, Ghazali; Khairel Rafezi, Ahmad; Faizul, Che Pa; Mohd Fitri, Mohamad Wahid; Murizam, Darus (Universiti Kebangsaan Malaysia (UKM), 2008-12-03)
    The foundry engineer is usually familiar with the fact that there are different types of clay,such as kaolinite and montmorillonite (bentonite). The bonding action of kaolinite in moulding sands results from the free ionic ...
  • The application of Fluidity Spiral in sand-mold casting 

    Mohd Ichwan, Nasution; Mohd Nasir, Zainal Arif; Che Mohd Ruzaidi, Ghazali; Shamsul Baharin, Jamaludin; Khairel Rafezi, Ahmad; Faizul, Che Pa; Mohd Fitri, Mohamad Wahid; Murizam, Darus (Universiti Kebangsaan Malaysia (UKM), 2008-12-03)
    The term fluidity is always used in the cast-metals industry. Fluidity is the reciprocal of viscosity. The foundryman job is to search the amount of quantity that will permit him to evaluate the relative ability of a given ...
  • Comparative Study on Mechanical Properties and Microstructure of Binary Aluminium Alloy using Sand and Green Sand Molds 

    Mohd Ichwan, Nasution, Ir.; Shamsul Baharin, Jamaludin, Assoc. Prof. Dr.; Che Mohd Ruzaidi, Ghazali, Assoc. Prof.; Faizul, Che Pa (Universiti Malaysia Perlis (UniMAP), 2007-06-09)
    Products of binary system especially for aluminium alloys and others binary are of great use.However, mechanical properties of these products are still low because of wrongly chosen the types of molds. Therefore,it is ...
  • Study on Influence of Silicon Percentage on Flowability of Binary Aluminium-Silicon Alloy 

    Mohd Ichwan, Nasution, Ir.; Shamsul Baharin, Jamaludin, Assoc. Prof. Dr.; Che Mohd Ruzaidi, Ghazali, Assoc. Prof.; Faizul, Che Pa (Universiti Malaysia Perlis (UniMAP), 2007-06-09)
    Study on flowability of liquid of binary aluminium-silicon with the difference percentage of silicon is carried out by using CO2 mold and with the spiral pattern. The result showed that flowability of molten metal of ...
  • New Approach to Aluminium-Polymer Alloys 

    Mohd Ichwan, Nasution; Mohd Nasir, Zainal Arif, Prof.; Che Mohd Ruzaidi, Ghazali, Assoc. Prof.; Shamsul Baharin, Jamaludin, Assoc. Prof. Dr.; Faizul, Che Pa; Murizam, Darus; Che Idrus, Omar; Lee Liu Mei (Universiti Malaysia Perlis (UniMAP), 2007-06-09)
    New approach to aluminium-polymer alloys prepared by in-situ mixing or addition of molten metal onto polymer granules will be highlighted. This concept is simple and never been attempted before due to the thermal instability ...

View more