Browsing Khairel Rafezi Ahmad, Associate Prof Dr. by Title
Now showing items 7-26 of 39
-
Effect of age hardening on Aluminum alloys: a study of motorcycle piston
(Universiti Malaysia Perlis, 2009-12-01)This paper reported on the effect of age hardening on the aluminum alloys piston. These studies were carried out to improve the hardness of the aluminum alloys piston by using age hardening method. The AlSiCuMg alloys with ... -
Effect of different nickel content on the mechanical properties of hydroxyapatite-ni composites from coated powders
(Trans Tech Publications, 2014)HA-Ni composites were fabricated by uniaxial pressing from coated powders, in which HA particles were successfully coated with nickel precursor by the electroless deposition method. The compacted powders sintered at ... -
Effect of Inhibitors on the Corrosion of AISI-1018 Steel in Sea-Water Environment
(Research India Publications, 2008)The inhibitive properties of sodium benzoate for AISI-1018 steel controlling corrosion were studied in seawater environment at atmospheric condition. Three sets of solution were prepared with the concentrations of 0.3M, ... -
Effect of roughness of hypo-and hyper-eutectic Al-Si piston alloy on wear characteristics under lubrication
(Malaysian Technical Universities Network (MTUN), 2012-11-20)The tribological behavior of tow AlSi alloys under the influence of surface roughness average was investigated for the present study. The silicon content of these alloys ranged 10 and 16-wt% Si, and includes hypoeutectic ... -
Effect of roughness of hypo-and hyper-eutectic Al-Si piston alloy on wear characteristics under lubrication
(Elsevier B.V., 2013)The tribological behavior of tow Al-Si alloys under the influence of surface roughness average was investigated for the present study. The silicon content of these alloys ranged 10 and 16-wt% Si, and includes hypoeutectic ... -
Effect of spot welding current and cycles on the mechanical properties of welded galvanized steel sheets
(Trans Tech Publications, 2013)Studies on the effects of welding current and cycles were carried on the galvanized steel sheets using spot welding. The welding currents used were 3 kA, 5 kA 6 kA and the welding cycles were 4, 6 and 8. Tensile shear and ... -
Effect of temperature of oxalic acid on the fabrication of Porous anodic alumina from Al-Mn alloys
(Hindawi Publishing Corporation, 2013)The influence of temperature of oxalic acid on the formation of well-ordered porous anodic alumina on Al-0.5 wt% Mn alloys was studied. Porous anodic alumina has been produced on Al-0.5 wt% Mn substrate by single-step ... -
The effects of solutionizing temperatures on microstructures of as-received A357 alloy
(Universiti malaysia Perlis, 2009-12-01)Solution treatment has been carried out on as-received A357 alloy at two solution treatment temperatures of 530ºC and 550ºC for 11 hours. The microstructural study was performed by using optical microscope. Optical ... -
Electrochemical measurement of PBS using cyclic voltammetry and AAO fabricated at ambient temperature and low potential
(Trans Tech Publications, 2013)Anodic aluminium oxide fabricated at ambient temperature and low potential in phosphoric acid electrolyte was used as the working electrode for the electrochemical measurement of phosphate buffer saline under different pH ... -
Evaluate the effects of various surface roughness on the tribological characteristics under dry and lubricated conditions for Al-Si alloy
(Scientific Research Publishing Inc. All rights reserved., 2012-07)The effect of surface roughness average of hypereutectic aluminum silicon alloys (with 16 wt% Si) on the friction and wear was investigated. Various surface roughness average (Ra) of different degrees was verified as well ... -
Fire resistance of biomass ash panels used for internal partitions in buildings
(Malaysian Technical Universities Network (MTUN), 2012-11-20)constructions. This study develop new products made of by biomass ash from industry waste for the internal partitions panel. Modifying the internal partition panel of wall with addition of biomass ash (EFB) and clay soils ... -
Fire resistance of biomass ash panels used for internal partitions in buildings
(Elsevier B.V., 2013)This study was to develop fire-resistant panels with a high biomass ash ratio from the combustion of EFB at an industrial scale to be used in different fire-resistant internal partitions in buildings and industrial ... -
The influence of welding parameters and corrosive environment on the joint strengh of resistance Spotwelded Mild Steel Sheets
(Universiti Kebangsaan Malaysia (UKM), 2008-12-03)In the present work, mild steel sheets consisting two batches were welded by resistance spot welding at different welding parameters and exposed under different environments. The 5% sodium chloride brine was used in the ... -
The influence of welding parameters and corrosive environment on the joint strength of resistance spot-welded mild steel sheets
(Universiti Malaya, 2009)In the present work, mild steel sheets consisting two batches were welded by resistance spot welding at different welding parameters and exposed under different environments. The 5% sodium chloride brine was used in the ... -
The influence of welding parameters and corrosive environment on the joint strength of resistance spot-welded mild steel sheets
(University of Malaya, 2009)In the present work, mild steel sheets consisting two batches were welded by resistance spot welding at different welding parameters and exposed under different environments. The 5% sodium chloride brine was used in the ... -
Intermetallic compound formation on solder alloy/cu-substrate interface using lead-free sn-0.7cu/recycled-aluminum composite solder
(Scientific.Net, 2012-12)Feasibility of using recycled-Aluminum (re-Al) as reinforcement particulates in Sn-0.7Cu is assessed by powder technology method, whereby re-Al particulates are produced from discarded aluminum beverage cans. This paper ... -
Kinetic and thermodynamic studies on adsorption of copper ions onto pomelo peel (citrus grandis)
(Trans Tech Publications, 2013)The ability of pomelo peel (PP) as natural adsorbent to remove Cu (II) ions from aqueous solution was investigated. The influence of solution pH, contact time and temperature were evaluated. Cu (II) removal increased as ... -
Mechanical properties of dissimilar welds between stainless steel and mild steel
(Trans Tech Publications, 2013)Joining of stainless steel type 304 to mild steel was carried out using a gas tungsten arc welding (GTAW). Samples were welded using stainless steel welding electrode: (AWS: E308l-16) and mild steel welding electrode: (AWS: ... -
Novel of Binary Metal-Non Metal Material for Chair Flower Product (Novel AI - PP for Chair Flower Product)
(Universiti Malaysia Perlis, 2009)Material for aluminium product usually made from aliminium scrap. Nowadays, the price of aluminium scrap is increased. The idea is how to minimize the cost of production via minimize the weight of the product without ... -
Organic dye degradation with TiO2 catalyst/AAO template in the presence of H2O2
(Trans Tech Publications, 2013)In this study, anodic aluminum oxide (AAO) fabricated from phosphoric acid electrolyte at ambient temperature was used as the porous template, while a sol gel procedure was used for the preparation of the TiO2 sol with the ...