Browsing Final Year Project Papers & Reports by Title
Now showing items 1002-1021 of 2200
-
Fabrication and analysis of Microstrip bandpass filter for wireless LAN
(Universiti Malaysia PerlisSchool of Computer and Communication Engineering, 2007-05)This project presents the design of two types of bandpass filters parallel-coupled bandpass filter and hairpin filter. The filter is designed for a center frequency of 2.44 GHz with 100MHz operating bandwidth. The design ... -
Fabrication and characterization of Barium Strontium Titanate (BA1-XSRXTIO3 BST) for heat sensor application
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)Ferroelectric Barium Strontium Titanate (BST) thin films were successfully prepared by wet chemical deposition or sol-gel method and characterized using SPA, AFM, and sensing properties. The BST thin film was fabricated ... -
Fabrication and characterization of Ceramic Porcelain tiles
(Universiti Malaysia PerlisSchool of Materials Engineering, 2008-04)Fabrication of ceramic tiles requires detailed attention on the processing parameters such as raw material size and weight percentage, forming and drying process, and sintering temperature. The scope of the project is to ... -
Fabrication and simulation of PNP Bipolar transistor based on Spin On Dopant technique and Electrical characterization
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)In this project, the fabrication and simulation of pnp transistor was performed. From fabrication process, the electrical characteristic and sheet resistance of the device was observed by 4 point probe measurement. The ... -
Fabrication Of 50 µm transistor and AlNiAu interconnection process
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2007-03)Generally process fabrication transistor will starts by cleaning the wafer, formation region drain, D and source, S, get oxide and deposited aluminum as contact with the source, drain and gate. Mask is very important thing ... -
Fabrication of Al-based metallic glasses by mechanical alloying and hot consolidation
(Universiti Malaysia Perlis (UniMAP), 2017-04)This project is related to fabrication of aluminium based amorphous metallic glasses. Elemental powder of aluminium, copper and nickel were used for the purposed mentioned. The element powders with nominal composition ... -
Fabrication of graded Porous Hydroxyapatite by using coconut fibre
(Universiti Malaysia PerlisSchool of Materials Engineering, 2008-04)This study was carried out to develop sample hydorxyapatite (HA) cylindrical with have porous in particular part for example his external layers has solid part while on the inside it exist porous. Further it can make as ... -
The fabrication of heparin imprinted fiber membrane using electrospinning
(Universiti Malaysia Perlis (UniMAP), 2016-06)The studies of the fabrication of Heparin Imprinted Fiber membrane using Electrospinning was presented and investigated. This studies is about electrospinning method use to produce membrane from Polyvinylidene fluoride ... -
Fabrication of Magnesium-Hydroxyapatite composites targeted for biodegradable implant application
(Universiti Malaysia Perlis (UniMAP), 2016-06)In the present study, as a lightweight metal with mechanical properties similar to natural bone, magnesium is gaining wide popularity as biodegradable materials targeted for temporary implant applications. The objective ... -
Fabrication of Photoanode and its performance in Photocatalytic fuel cell
(Universiti Malaysia Perlis (UniMAP)School of Materials Engineering, 2016-05)Photocatalytic fuel cell system (PFC) is a new technology for simultaneous organic wastewater treatment and electricity generation. Different composition of photoanode and different layers of photoanode were fabricated ... -
The fabrication of porcelain ceramic via Wet casting technique
(Universiti Malaysia PerlisSchool of Materials Engineering, 2008-04)Porcelain ceramic which composed of ball clay, kaolin, silica and feldspar were fabricated and investigated to study the effect of sintering temperature on mechanical properties. Two types of parameter were used in these ... -
Face recognition using holistics features of low frequency infomation
(Universiti Malaysia Perlis (UniMAP)School of Computer and Communication Engineering, 2015-06)Face recognition has been getting the most attention from researchers in biometrics. Since the introduction of biometrics, it tried to find a process identified by comparing the current biometric pattern to the database. ... -
Face recognition using neural network
(Universiti Malaysia PerlisSchool of Mechatronic Engineering, 2008-03)This dissertation provides a study of camera-based face recognition research. There are two underlying motivations to conduct this project: the first is to study and analyze type of feature extraction method, and the second ... -
Factors influencing the formation of Disinfection By-Products (DBPs) in drinking water
(Universiti Malaysia Perlis (UniMAP), 2014-06)Disinfection for drinking water reduces the waterborne diseases caused by pathogen but it may pose chemical side effect to human health due to the formation of disinfection by products (DBPs) that form when the disinfectant ... -
Failure analysis simulation of polymeric foam composite using ANSYS 15.0
(Universiti Malaysia Perlis (UniMAP)School of Materials Engineering, 2016-05)Kajian ini menerangkan kesan multi tiubnano berdinding karbon (MWCNTs) ke atas sifat, terutama sifat-sifat busa poliuretana tegar (PU) dihasilkan daripada polyol minyak sawit (POP)dan metilena diphenyl diisosianat (MDI). ... -
Fan control and monitoring system using Visual Basic program
(Universiti Malaysia PerlisSchool of Microelectronic Engineering, 2008-04)This thesis is about the usage of a system to control and monitor a fan or more for certain kinds of operation and application in real life. This is including on how to control the fan speed manually or by using temperature ... -
Fatty acid methyl ester production from low value vegetable oil via alkaline catalyst
(Universiti Malaysia Perlis (UniMAP)School of Bioprocess Engineering, 2013-05)Biodiesel was one of the most promising alternative renewable fuels to substitute the conventional fossil fuel. In this tropic, the production of biodiesel from low value waste vegetable oil (WVO) via alkaline catalyzed ... -
Feasibility study and design of natural dehumidification method using desiccant for model house
(Universiti Malaysia Perlis (UniMAP), 2015-12)This case or research is feasibility study and design of natural dehumidification method using desiccant for model house. Desiccant dehumidification is function to improvise the nowadays heating, ventilation and air ... -
Feasibility study for a development of a mechanical agricultural cutter using pressurized air flow
(Universiti Malaysia Perlis (UniMAP), 2016-06)The aim of this study is to solve the problem of the use of rechargeable batteries for the Smart Harvester Cutter. Besides, to analyze the mechanisms employed to study the existing batteries and defects that occur during ... -
Feasibility study of a non-destructive fruit maturity testing system utilising capacitive properties
(Universiti Malaysia PerlisSchool of Computer and Communication Engineering, 2008-04)The classification for the maturity of fruits is not easily determined. This is especially true, for some fruits whose color have no direct correlation with to its level of maturity or ripeness. The levels of maturity can ...